Calculate the top and bottom stress at transfer stage and service stage. Consider three 0.6" Grade 270 seven wire strands. 500 mm 200 mm 500 mm 400 mm 300 mm Details: f'c (at release) = 27.5 Mpa f'c = 41.4 Mpa 0.6" Grade 270 seven wire-strand fej = 1364.5 MPa (initial) fer = 1294 MPa (final) Maw = 76.15 kN-m MSDL = 25 kN-m ML = 83.04 kN-m %3D %3D %3D %3D

Calculate the top and bottom stress at transfer stage and service stage. Consider three 0.6" Grade 270 seven wire strands. 500 mm 200 mm 500 mm 400 mm 300 mm Details: f'c (at release) = 27.5 Mpa f'c = 41.4 Mpa 0.6" Grade 270 seven wire-strand fej = 1364.5 MPa (initial) fer = 1294 MPa (final) Maw = 76.15 kN-m MSDL = 25 kN-m ML = 83.04 kN-m %3D %3D %3D %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The wood pole is supported by two cables of 1/4 in. diameter. The turnbuckles in the cables are tightened until the stress in the cables reaches 60000 psi. If the working compressive stress for wood is 200 psi, determine the smallest permissible diameter of the pole.
Determine the load capacity of the angle ASD. USE NSCP 2015.
A copper flat measuring 60mmx30mm is brazed to another 60mmx60mm mild steel flat as shown. If the combination is heated through 120 ℃, determine the stress produced in each of the bar. Concrete: ? = 18.5x10^-6/℃, ?? = 110 GN/?2 Steel: ? = 12x10^-6/℃, ?? = 220 GN/?2 Length of each flat = 400 mm.
Note: SN is equal to 18, topload will be equal to 118kN
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
Six 20-mm-diameter rivets fasten the plate to the fixed member. Determine the shearing stress caused in each rivet by the 40kN loads. What additional load P can be applied before the average shearing stress in any rivet exceeds 60MPa?
A rectangular bear has a wish of 300mm and a total depth of 650mm , calculate the area of steel reinforcement repral Take, M. 360kN.m f30 MPa and , 400MP
SITUATION 1 For the figure shown, the diameter of holes is 20mm. Steel plate is made up of 10 mmw250mm wth staggered sections in the accompanying figure. Resistance tactbr for the yielcing limit state=0.9 Fy=248.8MPa, Fu=449.3M Pa Load Factors: DL=1.2, LL=1.6 Res istance factor for the fracture limit=0.75 1. Compute the netwidth for the plate in consideration for block shear. Use LRFD method a. A-B-E Path b. A-D-E Path c. A-C-D-E Path d. A-C-D Path 2. Compute the maximum design strength of the connection in relation to the answer in no.l 3. Compute the maximum value of service load T when A36 steel is usec, the live load us four times the dead load
A 395 mm diameter short concrete post has 6-600 mm² steel bars reinforcing it. E(steel) = 200 GPa , E(conc) = 15 GPa. Assume that the allowable stress to be σ(steel) =160 MPa, σ(conc) = 8 MPa.1. Find the maximum allowable actual stress in steel. a. 203.12 MPab. 154.23 MPac. 106.64 MPad. 95.235 MPa3. Find the maximum allowable load. a. 1335.104 kNb. 1245.120 kNc. 1654.100 kNd. 1323.105 kN
Discuss Laboratory Shear Strength Tests
Discuss aboout Self-straining loads
Provide correct answer asap!! Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive stress in the punch is limited to 50 ksi. calculate the thickness maximum of the plate in which a hole of 2.5 inches in diameter can be drilled.