The uniform concrete slab has a mass of 2900 kg. The slab isheld in the horizontal plane by three parallel supporting cablesas shown. Suppose that F = 17 kN. (Figure 1)Part BDetermine the tension in the cable connected to B.Express your answer to three significant figures and include the appropriate units.HÀ?TB =ValueUnitsPart CDetermine the tension in the cable connected to C.Express your answer to three significant figures and include the appropriate units.HAPart ATc =ValueUnitsDetermine the tension in the cable connected to A.Express your answer to three significant figures and include the appropriate units.?TA =ValueUnits

Answered: Image /qna-images/answer/7ae8c01b-8c25-48de-9f42-77010e2b610b.jpg

The uniform concrete slab has a mass of 2900 kg. The slab is held in the horizontal plane by three parallel supporting cables as shown. Suppose that F = 17 kN. (Figure 1) Part B Determine the tension in the cable connected to B Express your answer to three significant figures and include the appropriate units. HA T3 = Value Units Part C Determine the tension in the cable connected to C. Express your answer to three significant figures and include the appropriate units. Value Units PartA Tc = Determine the tension in the cable connected to A. Express your answer to three significant figures and include the appropriate units. 圖] ? TA = Value Units

The uniform concrete slab has a mass of 2900 kg. The slab is held in the horizontal plane by three parallel supporting cables as shown. Suppose that F = 17 kN. (Figure 1) Part B Determine the tension in the cable connected to B Express your answer to three significant figures and include the appropriate units. HA T3 = Value Units Part C Determine the tension in the cable connected to C. Express your answer to three significant figures and include the appropriate units. Value Units PartA Tc = Determine the tension in the cable connected to A. Express your answer to three significant figures and include the appropriate units. 圖] ? TA = Value Units

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Similar questions

A pull of 6,500 lb is applied to a steel rod which has an ultimate stressof 65,000 psi. Determine the steel rod diameter if the factor of safetyis 5.A. 0.998 inch C. 0.798 inchB. 0.598 inch D. 0.398 inch
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter is reduced to 12.99265 mm. Determine: a. The modulus of elasticity. Answer: 200 GPa. b. Poisson's ratio. Answer: ν = 0.30 c. Shear modulus. Answer: G = 76.92 GPa. d. The deformation of the rod. Answer: δx = 0.09415 mm. Recommendation: Obtain the modulus of elasticity using the slope of the straight line.
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
I. Single-choice questions.: 5. Bridge piers belong to which part of a bridge? ( ) A. Bridge superstructure B. Bridge substructure C. Bridge deck system D. Bridge foundation 6. When calculating the load transverse distribution coefficient (m) near the bearing supports of a simply-supported beam bridge, which kind of calculation method is recommended? ( ) A. Lever principle method B. Hinge joint slab method C. Eccentric compression method D. G-M method
If possible, answer in 3 decimal places, thank you. For the wood beam shown in Figure A, assume L=1.5 m and P=8 kN. The beam cross section shown in Figure B has dimensions of b=47 mm and d=232 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? Calculate the reaction forces By and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown for the forces By and Dy on the free-body diagram below. (Note: Since Dx=0, it has been omitted from the free-body diagram.) By= kN Dy= kN Determine the shear forces VA⁢B, VB⁢C, and VC⁢D acting in segments AB, BC, and CD, respectively. Note that the shear force is constant in each of these segments. When entering your answers, use the shear force sign convention. VA⁢B= kN VB⁢C= kN VC⁢D= kN…
Three forces are applied in a system whose resultant is zero, one of the force is unknown: F1 (70lbs, 45deg NE), F2 (80 lbs, 65deg SE). Compute the horizontal force (lbs) of the unknown force.
Compute the stress in Mpa in a 90 cm pipe with a wall thickness of 9.50 mm if water fills it under a head of 70 m. a. 23.65 b. 32.53 c. 30.87 d. 27.67
A 5-kip crate is supported by a pulley system and a horizontal force P.a) Find P and the angle α. Report your answer in kips (1 kip = 1000 lbs).b) For this problem if you double the weight of the crate, will the force P double? Briefly explain why or why not.
Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 40*10 deep reinforced with the bars 20mm in diameter enclosed with 10mm diameter stirrups when the tensile steel strain is 0.008 and concrete strain is 0.003. f'c = 22MPa.
What is the bending stress in the beam 1.8 meters from point A? A.10.24 MPa B.9.60 MPa C.7.68 MPa D.8.60 MPa What is the bending stress 20 mm from the top of the beam 1.5 meters from point A? A.4.838 MPa B.10.442 MPa C.9.247 MPa D.7.225 MPa What is the shear stress in the beam at point A? A.0.80 MPa B.0.33 MPa C.1.57 MPa D.0.48 MPa What is the shear stress 80 mm from the top of the beam at point B? A.0.1024 MPa B.0.8072 MPa C.0.1966 MPa D.0.4096 MPa
A)Draw the M, N, T diagrams of the system. B)Calculate the M values at 25% intervals under distributed loads.