Answered: Calculate the weight due to ice on a…

Calculate the weight due to ice on a transmission line where the Total weight of conductor = 3.2 Kg/m, actual weight of conductor = 1.4 Kg/m, and weight due to wind = %3D 0.4 Kg/m.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.20P: Calculate the inductive reactance in /km of a bundled 500-kV, 60-Hz, three-phase completely...

See similar textbooks

Related questions

Q: Calculate the weight due to ice on a transmission line where the Total weight of conductor = 2.8…

A: We’ll answer the first question since the exact one wasn’tspecified. Please submit a new question…

Q: Why is the Geometric Mean Distance (GMD) of two different conductors the same in a transmission line…

A: GMR stands for geometric mean radius which is also known as self GMD it is mean of the distance of…

Q: The diameter of the overhead lines in the form of cylindrical conductors in a 300 kV three-phase…

A: Given diameter = 20mm, Vline = 300kV. Your b subpart is not clear I assume you have asked for…

Q: (b) A transmission line conductor with weight per unit of 1.55 kg/m is installed between two towers…

Q: A 3 phase 140 kV line with 43.715 cm of distance separation between the conductor so that corona…

A: According to question: Let the radius of conductor = r. Air density factor is calculated as…

Q: The towers of height 45 m and 85 m respectively support a transmission line conductor at water…

Q: Explain what will happen to the characteristic impedance when the spacing between the center of two…

A: We know direct formula of two conductor transmission line.

Q: DISCUSSION QUESTIONS 1. What is the effect of unsymmetrical spacing of conductors in a 3-phase…

A: Since you have posted the multiple questions so we are supposed to answer 1st one.

Q: 4.15 Find the GMR of a stranded conductor consisting of six outer strands surrounding and touching…

Q: Which among these is used to determine or compute for the Transmission Line AC Resistance? A.…

A: power losses = (current)2*Ac resistance where as dc resistance = resistivity×lengthcross sectional…

Q: A transmission line is supported from two towers at heights of 40 m and 58 m above ground level, the…

Q: E 5m A 7m 5m B 7m 7m C

Q: is desired to construct uniform transmission lines using polyethylene (εr = 2.25) as the dielectric…

Q: 7. Two towers of height 40 m and 30 m respectively support a transmission line conductor at water…

A: The tower and transmission line diagram can be made as: Difference between level supports is: h =…

Q: In transmission lines, the length of the line is small as compared with the distance of separation…

A: Transmission lines especially power lines are very long and they carry electric current over…

Q: A transmission line has a span of length 250 m and the weight of the conductor per metre length is…

A: The solution can be achieved as follows.

Q: An over head transmission line has a cross area of conductor of 4 cm and supported from two towers.…

Q: 1. A transmission line conductor is supported from two towers at heights of 70 m above water level.…

A: Given, Height of the two towers =70m Distance(l) =300m Tension(T) =1500kg Size of conductor(A)…

Q: A 3-phase, 440 kV transmission line consists of 2:5 cm radius conductor spaced 3 meters apart in…

Q: calculate capacitane, inductance, resistance and conductance of one type of transmission line by…

A: Transmission lines are conductors that serve as a channel for electrical waves (energy) to be…

Q: he geometric mean radius of the conductor in a 380 kV, 120 km long transmission line 24 mm. The…

A: Given that Vline=380 KV Vph=3803=219.40KVL=120 Kmr=242=12 mmd=3.2mroughness factor m0=0.98b=725 mm…

Q: Question 4 The line-to-line voltage of an overhead distribution line is 100 kV and radius of the…

A: Electric field intensity is given by: E(x)=V2xlndr

Q: Why is the Geometric Mean Distance (GMD) of two different conductors the same in a transmission line…

A: We have given the following problem

Q: 1. Find the GMR and GMD of the given stranded conductor with radius 1.3cm.

A: In this question, Find the GMR and GMD if radius of the conductor r= 1.3cm

Q: An over head transmission line has a cross area of conductor of 4 cm and supported from two towers.…

Q: Figure shows a stranded conductor identical strands each of having 7. radius r. Find the self…

A: Self GMD: this is also called as geometric mean radius. This is calculated for every phases. it does…

Q: Using sketch discuss the impact of following terms occurred in the transmission line conductors: i)…

A: (i) Corona effect :- Corona is the self electric discharge of atmospheric air. If the operating…

Q: Calculate the weight due to ice on a transmission line where the Total weight of conductor = 2.8…

A: Total weight of conductor is given wt=2.8 kg/m Actual weight of conductor is, w=1.8 kg/m Weight due…

Q: 3. A 3-phase, 220 kV, 50 Hz transmission line consists of 1-2 cm radius conductors spaced 2 m at the…

A: For the following data Corona loss is determined as shown below

Q: Example 2: Calculate maximum sag of a line with the conductor material over all diameter o.889cm,…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Calculate the weight due to ice on a transmission line where the Total weight of conductor = 3.6…

Q: 2. A 15-km, 60Hz, single phase transmission line consists of two solid conductors, each having a…

Q: 7. Two towers of height 40 m and 30 m respectively support a transmission line conductor at water…

Q: Question 4 The line-to-line voltage of an overhead distribution line is 100 kV and radius of the…

A: Field intensity variation between the lines is given as: E(x)=V2xlndr x is the variable in the above…

Q: Calculate the weight due to ice on a transmission line where the Total weight of conductor = 3.2…

A: Total weight of conductor=3.2kg/m Actual weight of conductor=1.8kg/m Weight due to wind=0.8kg/m

Q: if the conductor diameter decreases, inductance of the line is _______?

A: Although formula formula for inductance is given by L=(4π×10-7)lnd0.7788r (For…

Q: An overhead transmission line at a river crossing is supported from two towers at heights of 50 m…

A: The solution can be achieved as follows.

Q: The inductive reactance of the line conductor is 60 Ω per km, then the inductance of the conductor…

A: Inductance X= 60ohm/km Lenth L= 41km

Q: Calculate the weight due to ice on a transmission line where the Total weight of conductor = 3.6…

A: Total weight of conductor is given, wt=3.6 kg/m Actual weight of conductor is, w=1.6 kg/m Weight due…

Q: The per-phase line loss in a 40 km long transmission line is not to exceed 60 kW while it is…

Q: A microstrip line is composed of zero thickness copper conductors on a substrate having εr = 8.4,…

A: Given, εr=8.4W=0.5 mmh=1.5 mmfrequency of operation= 6 GHz Wh=0.5 mm1.5 mmWh=0.3333Wh=0.3333<1

Q: Calculate the weight due to ice on a transmission line where the Total weight of conductor = 2.8…

A: Need to find ice weight

Q: A 115 kv line has a horizontal configuration. The distance between adjacent conductors is 9ft. What…

A: The solution can be achieved as follows.

Q: The towers of height 45 m and 80 m respectively support a transmission line conductor at water…

Q: Prove that the conductor cost for transmission line is inversely proportional to the square of the…

A: Power suppied by source is cosntant VIcosϕ = constsant I∝1vlosses are also constant (I2R = constant…

Q: c) Figure 3 depicts a lengthwise cross-section of a coaxial transmission line, indicating the…

Q: Explain (brief description) what will happen to the characteristic impedance when the spacing…

Question

alcolathe weighEtiue toe on a transmiss
conductor 14 Ka and weight du
e" 13% "
o tap changing transformer
Clear my choice
Calculate the weight due to ice on a transmission line where the Total weight of
conductor = 3.2 Kg/m, actual weight of conductor = 1.4 Kg/m, and weight due to wind =
0.4 Kg/m.
In a short transmission line the line chargina current value is smaller than a medium
CAPS
LOCK
D F

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Overhead transmission-line conductors are bare with no insulating cover. (a) True (b) False
For the overhead line of configuration shown in Figure 4.33 operating at 60 Hz and a conductor temperature of 700C, determine the resistance per phase, inductive reactance in ohms/mile/phase, and the current-carrying capacity of the overhead line. Each conductor is ACSR Cardinal of Table A.4.
Figure 4.37 shows the conductor configuration of a three-phase transmission line and a telephone line supported on the same towers. The power line carries a balanced current of 250 A/phase at 60 Hz, while the telephone line is directly located below phase b Assume balanced three-phase currents in the power line. Calculate the voltage per kilometer induced in the telephone line.
A transmission-line cable with a length of 2 km consists of 19 strands of identical copper conductors, each 1.5 mm in diameter. Because of the twist of the strands, the actual length of each conductor is increased by 5. Determine the resistance of the cable if the resistivity of copper is 1.72-cm at 20C.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
Calculate the inductive reactance in /km of a bundled 500-kV, 60-Hz, three-phase completely transposed overhead line having three ACSR 1 113 kcmil conductors per bundle, with 0.5 m between conductors in the bundle. The horizontal phase spacings between bundle centers are 10, 10, and 20 m.
For the case of double-circuit, bundle-conductor lines, the same method indicated in Problem 4.27 applies with r' replaced by the bundles GMR in the calculation of the overall GMR. Now consider a double-circuit configuration shown in Figure 4.36 that belongs to a 500-kV, three-phase line with bundle conductors of three subconductors at 21 in. spacing. The GMR of each subconductor is given to be 0.0485 ft. Determine the inductive reactance of the line in ohms per mile per phase. You may use XL=0.2794logGMDGMR/mi/phase
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
Shield wires located above the phase conductors protect the phase conductors against lightning. True False
3. A transmission line has a span of 150 m between level supports. The cross-sectional area of the conductor is 1·25 cm2 and weighs 100 kg per 100 m. The breaking stress is 4220 kg/cm2. Calculate the factor of safety if the sag of the line is 3·5 m. Assume a maximum wind pressure of 100 kg per sq. metre. [4]
In a three-phase 220 kV, 60 Hz overhead transmission line, the conductors have an overall radius of 1.50 cm each and are arrange in delta foundation. Assuming that the air density factor of 0.90 and Irregularity factor of 0.95. If a critical disruptive voltage of 250 kV between the lines under normal weather conditions. Calculate the minimum spacing between the conductors that is required.
A three-phase, 50Hz transmission line with a length of "240" is given. It has values of “27” MVA, 0.8 reverse power coefficient and phase voltage “134” kV (phase-phase) for the end of line. Transmission line conductors are placed “3.2” meters apart. The conductors are known to have a resistance of 0.11ohm/km and a diameter of 1.6cm. Neglecting the leaks and using the π equivalent circuit; ( ε0=8.854*10^(-12) F/m, μ0=4*π*10^(-7) H/m) 1) Find the total impedance value of the line, the end of line current, the line voltage at the end of the line, the line head phase and the line beginning line voltage?