Calculate V₁ and V₂ in the circuit shown in Fig. 10.6. 40/60° V 492 30/0° V --710 292 Figure 10.6 For Practice Prob. 10.2. Answer: V₁ = 38.72/69.67° V₁ V₂ = 6.752/165.7° V. j4Q

Q: ngle phase 50 Hz motor takes 10A at 0.8 power factor lagging from a 240 V supply calculate: (i) The…

A: Given data: Current, I= 10 A Power factor, cos ϕ=0.8 (lagging)

Q: Qs-For the circuit Shown in Fig (3) - SOKA loo 2mA 43 50 PF 3MA a) By using approximate Parllel…

A:

Q: Find V. for the circuit given below. R₁ 9+V/cc -Voc A₁ R₂ www 9+ Voc A₂ -Vec Vo

A:

Q: Find the total energy stored in the circuit of Figure below 602 L₁ = 2 mH 30 L₂=4mH C₁ = 20 µF C₂ =…

A:

Q: How can you use a common anode seven segment display given a 7448  decoder? What will you do to make…

A: The seven segment displays are of two circuit configurations, Common-anode type Common-cathode type…

Q: Qs-For the circuit Shown in Fig (3) - SOKA loo 2mA 43 50 PF 3MA a) By using approximate Parllel…

A:

Q: QI: A synchronous motor having a power consumption of 50 kW is connected in parallel with a load of…

A:

Q: Q2) Find the x(t) signal is Energy or Power signal? x(t) = 1e-²t.u(t))

A:

Q: 3: Find the truth table of the logic circuit shown below: MUX 83 B DO 0 0 1 0 1 23 EN D 180 But…

A:

Q: A load of 10 MW operating at a power factor of 0.5 lagging is connected to a 400 V, 60 Hz source.…

A:

Q: What is the difference between balanced and unbalanced line transmission lines, show the difference…

A: Difference between balanced and unbalanced line transmission lines

Q: 1. For the circuit shown in Figure 1, the transistor parameters are ß = 100 and V₁ = ∞. Design the…

A:

Q: For the circuit shown in Fig.(4) find the value of E, such that the current in the 5+j4 2 impedance…

A:

Q: Q3) An 380V 880VA, 220V, 50Hz, load has a power factor of 0.8 lagging. What value of parallel…

A:

Q: 1. Z-Transform is a convenient tool in designing, analyzing and representing digital signals. 2.…

A: Since multiple questions are present, as per the guidelines, only the first question will be solved.…

Q: 14. Determine the Q waveform relative to the clock if the signals shown in Figure 7-83 are applied…

A:

Q: What do you mean by fractional sampling rate conversion? Explain with an example of converting 48…

A: Sample rate converter is the change stream of discrete sample from another different sample rate. In…

Q: A square plate residing in the x-y plane is situated in the space defined by -3 m ≤x≤3 m and -3…

A:

Q: Calculate the value of the vector current density in cylindrical coordinates at PB(1.5, 90°, 0.5) 2…

A:

Q: Diagram showing zero basing in field effect transistors as applied in electronics

A: The Field Effect Transistor is a semiconductor device which consists of two PN-junctions. This is a…

Q: It is expected that a parallel RLC resonant circuit has a midband current 25 mA, when s applied to…

A: The mid-band current of the parallel RLC circuit is known, the impedance at the mid-band gain is…

Q: A non alternating periodic waveform has shown in figure. Find its form factor. ↑ 1A 0.5 A 10 20 40…

A: Given graph is:-

Q: When two identical parallel wires are 3 m apart, the inductance per unit length is 2.5 μH/m.…

A: We need to find out diameter of wire for given inductance

Q: Referring to the given circuit, what is ZTH if R₁ is changed to 220 ?

A: Resistance in parallel- 1/Req=1/R1+1/R2+1/R3+...........   Resistance in series-…

Q: Define the terms a) balanced system or symmetrical system b) phase sequence c) balanced load

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Question 10: Design an FIR linear-phase, digital filter approximating the ideal frequency response…

A: The Given ideal frequency response is Hdω=1,    for ω≤π30,   forπ3<ω≤π To design a FIR…

Q: Determine the Laplace transform of the signal x(t) in Figure Q1(a) and state its region of…

A:

Q: Using voltage-divider biasing, what is the voltage at the gate VGs? express answer in volts Vcc 20 V…

A:

Q: Q1) A) What is bus? How many ways to construct bus system. (explain with example for one type)

A:

Q: Eş merkezli r1 ve r2 yarıçaplı iki iletken çember merkezleri orijin olacak şekilde…

A: We need to find out the value of charge for given electric field

Q: Vin For the circuit shown, assume that Vo = 3V and that the transistor is described as follows: Kn =…

A: For the above given question we need to perform AC and DC analysis of the given amplifier.

Q: Question 1 (a) For the circuit shown in Figure 1.1 write down the AC mesh equations using phasor…

A: The given circuit diagram is shown below: It is given that: vst=5 cos400t-45° V=5∠-45° VL=30…

Q: Solve for vo(t) in the circuit given by using superposition principle. OMNIA 692 2 H m 12 cos 31 V %…

A: Ggiven here a electrical circuit and asked to find the voltage v0.

Q: Determine the Laplace transform and the associated region of convergence and pole-zero plot for each…

A: Given  Few signals.we need to determine the Laplace transform of the given signals. Please find the…

Q: What do you understand by impedance matching? Also write the formula of characteristic impedance for…

A: Impedance is the total opposition of flow of the electrical current in a  Alternating circuit. It is…

Q: A CS JFET amplifier has a load resistance of 10 kQ. Rp= 8200. If 8m - 5ms and Vin= 500 mV, the…

A: Given, A CS amplifier has Load resistance, RL=10 kΩ RD=820 Ωgm=5 mSVm=500 mV

Q: :A/ Fill in the blanks with suitable words: Select TWO only 1. The Gauss's law in differential form…

A: This question belongs to electro magnetic field theory .  Problem can be solved such as following…

Q: Vols) 3 5+85+18 How?

A:

Q: arm resistance of wheatstone bridge are. r1=200ohm r2=400ohm r3=500ohm r4=600ohm input is e=5v…

A:

Q: For the circuit shown: 1. Find the value of "R" that makes the circuit in resonance. 2. Determine…

A: It is given that:

Q: Write TRUE if the statement is correct but if it’s false, change the underlined word or group of…

A: In this question , we will write about MOSFET related question.... Note :- as per our guidelines , I…

Q: What are the characteristics of an ideal operational amplifier?

A:

Q: ra FET, graph is drawn by taking voltage VGs in X axis and drain current in Y s, if the value of X…

A:

Q: The average value of a sinusoidal current is 300A. What is it’s rms value? Group of answer choices…

A:

Q: for the electron Find the momentum of the crystal for the electron if you know that its wavelength…

A: The wavelength of the electron is,  λ=1.2×10-10 m Using the De Broglie's relation, the wavelength is…

Q: 5 Find the average value of the periodic function shown in figure. VIMA 0 π/3 2π/3 4/3 5/3 2π [Ans:…

A:

Q: Q.3 The bode plot of the open-loop transfer function G(s) of a unity negative feedback system is…

A: The bode plot of the open-loop transfer function G(s) of a unity negative feedback system is…

Q: Q2: A generating station has a maximum demand of 25MW, a load factor of 60%, a plant capacity factor…

A: This question belongs to power system . It is based on the concept of plant . Have a look at the…

Q: In a linear circuit the super position principle can be applied to calculate the O Voltage and power…

A: In this question we will write about superposition theorem.....

Q: Solve the following problems. Use four decimal places for accuracy 2. A three phase, three wire,…

A:

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.