Chapter 2: 6. Angular units of measurement are specified either in 7. Each feature must be and of the feature. 8. Dimensions must be selected and arranged to suite the function and mating relationship of a part and must not be subject to more than one 9. Unless otherwise specified, all tolerances and datum features apply for the full 10. Unless otherwise specified, all dimensions and tolerances are applicable at 11. What are the three types of direct tolerancing methods? 12. Where specifying decimal inch dimensions, a or . Those dimensions specifically identified as reference, maximum, minimum, or stock do not require the application of a tolerance. (temperature). Compensation may be made for measurements made at other temperatures. and is never placed before the decimal point for values less than one inch.

Chapter 2: 6. Angular units of measurement are specified either in 7. Each feature must be and of the feature. 8. Dimensions must be selected and arranged to suite the function and mating relationship of a part and must not be subject to more than one 9. Unless otherwise specified, all tolerances and datum features apply for the full 10. Unless otherwise specified, all dimensions and tolerances are applicable at 11. What are the three types of direct tolerancing methods? 12. Where specifying decimal inch dimensions, a or . Those dimensions specifically identified as reference, maximum, minimum, or stock do not require the application of a tolerance. (temperature). Compensation may be made for measurements made at other temperatures. and is never placed before the decimal point for values less than one inch.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.5: Quality Assurance, Process Planning, And Quality Control

Problem 5RQ: What is the important factor to consider when choosing the proper measuring tool to inspect a...

See similar textbooks

Similar questions

Use BS 4500A:1970 to determine the dimensional tolerance on the critical diameters in Gear Sub- assembly. The following tolerance should be determined (the limits and fits at each interface will be provided by Canvas): i. Bush & Shaft: Critical Diameter is 35 mm; (H8/f7) ii. Housing & Bush: Critical Diameter is 45 mm; (H7/s6) iii. Gear & Shaft: Critical Diameter is 20 mm (for the Right Gear) (H7/k6)
Refer to the Ø.8740 ± .0005 dimension.A) Where is the tolerance specified ? ____________________________ B) Is its tolerance unilateral or bilaterial ? _________________________ C) What is its tolerance ? _____________________________________ D) What is the MMC, ? ________________________________ E) What is the LMC,? _________________________________
What is the important factor to consider when choosing the proper measuring tool to inspect a dimension?
Refer to the 1.914 dimension. A) Where is the tolerance specified ? _________________________________ B) What is its tolerance ? ________________________________C) What is the MMC? ______________________________ D) What is the LMC? _______________________________
Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 40 (+0.06 )/(+0.00 ) mm and Shaft = 40 (-0.07)/(-0.015) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Refer to the Ø.8740 ± .0005 dimension. D) What is the MMC,(Maximum material condition) ? ________________________________ E) What is the LMC,?(least material condition) _________________________________ Refer to the 1.914 dimension. Where is the tolerance specified ? _________________________________
Problem (2): Determine tolerance value and limit dimension of the rod which a diameter is ∅47 mm (nominal size), according to the e6 limit deviation (∅47e6). es=-25 mkm, ei=-41 mkm. Determine the basic size, tolerance and limit dimensions.
Refer to the 1.914 dimension. B) What is its tolerance ? ________________________________C) What is the MMC? (maximum material condition) ______________________________ D) What is the LMC(least material condition)? _______________________________
Please Fill In the blanks where I have marked red X's using the questions and Image below. 1. On the drawing above, before any geometric controls are applied, what is the coaxility tolerance is implied between the diameters? 2. On the part above, apply datum feature symbols to create a datum axis A-B by using the right and left diamters. 3. Apply a position coaxility between the right and left diamter of 0.1 at MMC. 4. Apply a position tolerance to the large center diameter within a diameter of 0.3 in relation to the single datum axis established by both datum features A and B.
Problem (7): Determine tolerance value and limit dimension of the rod which a diameter is ∅25 mm, according to the H9 limit deviation (∅25H9). ES=-12.7 mkm, Eİ=+0 mkm. Determine the basic size, tolerance and limit dimensions.
Identify the primary, secondary and tertiary datums associated with the positional geometric tolerance placed with the Ø.875±.005 dimension?
I need help please. Apply a dia 0.5 at MMC straightness control to the axis of the part above and draw the resultant tolerance zone and virtual size on the sketch of the produced part below. The image and question are also attached.