One particular zone served by a multizone air handler has a design cooling load of 1750 Btu/hr (0.5 kW) with a SHF of 0.8. The coil has air entering at 84 F (29 C) db and 70 F (21 C) wb with air leaving at 50 F (10 C) db and 90% relative humidity (RH). Zone conditions are 75 F (24 C) db and 50% RH. (a) What amount of air must be supplied to the space? (b) At what condition is the air supplied to the space? (c) How much air flows over the coil and how much air bypasses the coil for this one zone? Assume sea-level pressure.

One particular zone served by a multizone air handler has a design cooling load of 1750 Btu/hr (0.5 kW) with a SHF of 0.8. The coil has air entering at 84 F (29 C) db and 70 F (21 C) wb with air leaving at 50 F (10 C) db and 90% relative humidity (RH). Zone conditions are 75 F (24 C) db and 50% RH. (a) What amount of air must be supplied to the space? (b) At what condition is the air supplied to the space? (c) How much air flows over the coil and how much air bypasses the coil for this one zone? Assume sea-level pressure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the T2, T4, and Thermal Efficeincy
find the gage pressure reading if the ideal gas constant of air is 53.3 ft-lb/lbm-R. If one lbm of air is heated in a 0.5-ft3 tank at 200°F. Answer Choices: (a. 405.6 psig b. 473.9 psig c. 438.1 psig d. 490.2 psig)
Match each type of process (isobaric - isochoric -adiabatic ) 1- Apressure vessel which is experiences a temperature rise over the day 2- Compression of gas takes place in an insulated piston cylinder 3- A frictionless vertical piston cylinder arrangement which experiences 30j of heat
Saturated R-410A at a pressure of 95 psig will change at a temperature of A. 295 F B. 29 F C. 95 F D. 118 F
Derive the MEPotto in terms of P1, rk, rp, k, and e.
In a piston-cylinder assembly, there is initially 2 kg of water at a temperature of 25 °C and a pressure of 100 kPa. Then heat is given to the water until its volume is 0.4 m3. At this point, the piston in the cylinder is fixed with a stopper, but the water in the cylinder continues to heat until its temperature reaches 300 oC. According to this, calculate a) the final pressure of the water, b) the amount of heat given to the water, c) the work done by the piston. d) Show these processes in the T-v (Temperature-Specific Volume) diagram
(1) Specify whether the steam is wet, dry, or super-heated for the following conditions: (g) p = 4.0 MPa, a = 5.897 k.J/kg•K (h) p = 15.0 MPa, t =- 310°C
An electric windshield defroster is used to remove 0.25-in of ice from a windshield. The properties of the ice are Tsat = 328F, uif = hif = 144 Btu/lbm, and v = 0.01602 ft3/lbm. Determine the electrical energy required per square foot of windshield surface area to melt this ice and remove it as liquid water at 328F. What is the minimum temperature at which the defroster may be operated? Assume that no heat is transferred from the defroster or ice to the surroundings.
Problem 3: A large room contains a volume of air of Va = 11 m3 at a temperature of Ta = 55° F. It also contains a bathtub holding a volume of water of Vw = 0.51 m3 at a temperature of Tw = 111° F. Parts (a), (b), (c) are already complete. Just need parts (d) and (e). Part (a) If the density of the air at Ta is ρa = 1.25 kg/m3, calculate the mass of air in the room in kilograms. ma = 13.75 Part (b) If the density of the water at Tw is ρw = 1000 kg/m3, calculate the mass of the water in the bathtub in kilograms. mw = 510 Part (c) Take the room and water as an isolated system. Write an equation for the equilibrium temperature of the system T in terms of ma, Ta, mw, Tw, and the specific heat capacity of the air ca and the water cw. T = ( mw cw Tw + ma ca Ta )/( mw cw + ma ca ) Part (d) Calculate the final temperature of the system in kelvin, assuming a constant specific heat for the water of cw = 4180 J/kg⋅K and a constant specific heat capacity for the air of ca = 1010 J/kg⋅K.…
A 10 gallons of water has an inital temperature of 25 degrees Celsius. What is the input power needed to raise the temperature up to the boiling point after 25 minutes Assume heat loss 12%
10 kg of food has a moisture content of 260% (dry basis), is dried to a moisture content of 50% wet basis Determine the amount of water lost (kg) Answer:
The cooling system of a car engine contains 20.0 L of water (1L(1L of water has a mass of 1kg1kg ).a. What is the change in the temperature of the water if the engine operates until 836.0 k of heat is added?