ChivenCoupling is 4340-HT Steel (E = 205 [Crpa], Ct = 80 cpa, Gy:V = ૦.૧૦ ) .Diameter of bolt hole is1bolt pattern diameter is D=19.62 cmout side diameter of flange is OD = 25 cm and applied torque is 4.00 e + 04 [N-m]- Find The thickness of the thing flange t such that the maximumbearing, shear and normal stresses do not exceed allowable limits?E-ÑTOd =1 смOLDT-= 470 GPa 6-7454PaOD EdDOD

Given: The Elastic modulus of the material used, E = 205 GPa The shear modulus of the material used,…

Chiven Coupling V = 0.290). is 4340-HT Steel (E = 205 [C+Pa], G+ = 80 cpa, 6y = 470 GPa, 6₂ = 7195 ² u diameter is D=19.62.com &- d Diameter of bolt hole is 1 cm / out side diameter of flange is 00 = 25 cm = - Find the thickness of the thing flange t such that the maximum bearing, and shear and normal stresses do not exceed allownable limits? T a 00 bolt pattern and applied torque is 4.00e + 04 [N-m] ODEd Of DOD

Chiven Coupling V = 0.290). is 4340-HT Steel (E = 205 [C+Pa], G+ = 80 cpa, 6y = 470 GPa, 6₂ = 7195 ² u diameter is D=19.62.com &- d Diameter of bolt hole is 1 cm / out side diameter of flange is 00 = 25 cm = - Find the thickness of the thing flange t such that the maximum bearing, and shear and normal stresses do not exceed allownable limits? T a 00 bolt pattern and applied torque is 4.00e + 04 [N-m] ODEd Of DOD

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Data:P = 2 kipd = 3.6 inchw = 305 millimeterst = 0.03 meterr = 5.08 centimeterh = 0.6667 feet a) Calculate the maximum static stress in the material (in MPa). b) Estimate the theoretical stress concentration factor at the fillet c) Estimate the theoretical stress concentration factor at the hole
15 - A) -900 i + 3500 j + 3200 k NmB) -900 i - 3200 j + 3500 k NmC) -3200 i + 3500 j + 900 k NmD) 3500 i + 700 j + 3200 k NmE) -3200 i + 900 j + 3500 k Nm
Read and Solve carefully please Write clearly and Box the Final answer Express your answer to 3 Significant figures and include appropriate units. QUESTION : Recall that for spings the Zimmerli point on the modified Goodman diagram is located at (Ssm, Ssa) = (55, 35) ksi. Suppose that a particular spring wire has a shear ultimate strength of Ssu = 89 ksi. Determine the shear endurance limit of the spring wire. Give your answer in units of ksi,
α= 70o Kba = 0.33; t = 0.3”; R = 0.8”; L1 = 12”; L2 = 9”; w = 2.1”; D = 3.2” Using; Find the Starting Blank Size: width = _______ inches length = ___________ inches Kbf = 1.33; E = 10,000,000; TS = 36,000 psi; Find the Bending Force Required in a V-Die = ____________________ lbs.
6 6 - A) -22.124 j NmB) (-22.124) k NmC) (-42.124) i NmD) (-12.124) i NmE) (-32.124) j Nm
Shaft length, L and a different allowable maximum shear stress, τmax and subject to a different Torque, T. For steel use a shear modulus, G=81,000 MPa. A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate: a) The minimum shaft diameter required. b) The angle of twist over the length of the shaft. c) The Power output if your shaft is rotating at 2000 rpm. L= 1.6m, τmax=100MPa , T=1.3kN-m
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) Power transmission =60 kW,(ii) Shaft speed = 160 rpm,(iii)The angle of twist / m length = 1.1º(iv)Maximum twisting moment is 30% greater than its mean. (v) Take Modulus of rigidity as 105 Gpa. (i) Mean torque of the shaft (unit in Nm) = (ii)Maximum torque of shaft (unit in Nm) = (iii) The diameter of the shaft (unit in mm) = iv) Maximum shear stress in the shaft (Unit in MPa) is
Write 2 or more conditions for lamella eutectic structure to form.
Shown below is a figure of a landing gear configuration on the VS and VD planes (for landing gear the directions V, D, and S are often used instead of x, y and z) This gear unit is assumed to represent one side of the main gear on a tricycle type of the landing gear system. The loading assumed corresponds to a condition of nose wheel up or tail down. The design load on the wheel is vertical and it s magnitude for this problem is 15,000 lbf. Determine the reactions at F, H, and G. The fittings at F and H are pinned and therefore cannot transmit any bending moments. The fitting at G is also a pinned fitting.
The motion transmitted between the teeth of gears in mesh is *
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) the diameter of reference circle, d2=( )mm the diameter of addendum circle da2 =( )mm the diameter of dedendum circle df2 =( )mm
mechanical engineering (Machine design) (1)Find the torque and power that a shaft with a diameter of d=50 mm can safely carry at n=200 rpm. (safe shear stress value will be taken as Sem-80N/mm² for the shaft material).