mechanical engineering (Machine design) (1)Find the torque and power that a shaft with a diameter of d=50 mm can safely carry at n=200 rpm. (safe shear stress value will be taken as Sem-80N/mm² for the shaft material).

mechanical engineering (Machine design) (1)Find the torque and power that a shaft with a diameter of d=50 mm can safely carry at n=200 rpm. (safe shear stress value will be taken as Sem-80N/mm² for the shaft material).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: Below is the arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear A.…

A: Given:The gear A rotates clockwise CW.Gear B and C are on the same shaft and gear D and E are on…

Q: A horseshoe player releases the horseshoe at A with an initial speed vo= 36 ft/sec. Determine the…

A: According to the given datav=36ft/sSA=2.9ft andSB=11in=0.917ftSAB=-2.9+0.917=-1.983 ftWe need to…

Q: What are the key factors that affect the performance of a centrifugal pump in a fluid flow system,…

A: Centrifugal pumps play an integral role in various industrial and domestic applications to transport…

Q: Determine the deflection of point B

A: Given DataPortion AB made of steelThe Youngs modulus of the steel The Coefficient of thermal…

Q: X A 4 M L₂ B B L3 LA Ls Y C Pipe ABC is supported by three smooth journal bearings, Find the…

A: Given information: F=480lbsM=180 lb-ftangle =45 degree.

Q: The bar BC in the figure (Figure 1) rotates with an angular velocity w = 6 rad/s and an angular…

Q: determine the magnitude of the yo-yo's angular velocity

A: Given DataMass of the yo-yo =200 g =0.2 KgThe force The outer radius of the yo-yo The inner radius…

Q: Consider a steam power plant operating on the ideal Rankine cycle. The boiler is maintained at 4…

Q: In the continuous and incompressible flow of water with a temperature of 20°C and a density of 998…

Q: A rigid, massless, uniform beam of length L = 2 m is supported by rocker supports at A and B and…

Q: This question is made of two separate parts related to figures 1 and 2. 2 m F a Figure 1 2m The…

A: Note :- as per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: -b Fm A C W X ¦Y

Q: A Venturimeter having inlet diameter 1.8 cm and throat diameter 0.5 cm. The oil-mercury differential…

A: Given data as below:Inlet Diameter = 1.8 cm = 0.018 mThroat Diameter = 0.5 cm = 0.005 mOil-mercury…

Q: A model rocket is launched from point A with an initial velocity vo of 84 m/s. Also, the rocket's…

A: The initial velocity of rocket Distance

Q: (2) The correct calculation for determine the displacement at Point C of the following beam by using…

A: As per graph multiplication method of displacement at a point, displacement is given by…

Q: (c) An electronic PI temperature controller has an output p of 15 mA when the set point equals the…

A: In the problem, the following information was provided:The PI temperature sensor step response is…

Q: The system is at rest with the spring unstretched when theta = 0. the 5.3 kg uniform slender bar is…

A: mass,m=5.3 kgb=0.45 mto determine:(a) Spring constant k(b)magnitude of angular velocity

Q: A force of P = 20 N is applied to the cable, which causes a 175 kg of radius of Gyration KG = 0.42m…

A: To calculate the work done by the force of 20 N for 2 revolutions, we need to find the distance…

Q: Required information The structure consists of pin-connected members. Take X= 4 kN. NOTE: This is a…

A: Given

Q: A trough whose cross section is an equilateral triangle with side a = 3 m long is filled with water.…

A: Given:Triangle is givenSide, a= 3m To find:Force due to the water pressure on the one end of the…

Q: Consider the mechanism of Bar AB, Bar BC, and roller A. Roller A is constrained to move along the…

Q: Air flows over a stationary flat plate at speed of 4,5 m/s . Plate has a width of 1 m. Air has a…

Q: 400 mm Fr= 800 N 150mm -Ft= 600 N Fa = 4,00 L 450mm Draw bending torsional moments, shear forces and…

A: The force acting at gear C in negative y-direction , Fr = 800 NThe force acting at gear C in…

Q: 6.* Figure 6 shows two plates of thickness t = 6 mm and width (into the paper) 50 mm tha are joined…

A: please refer handwritten solution

Q: What is Pwall/0.2885? what number is Pwall?

Q: Consider an electrically heated brick house (k=0.40 Btu/h-ft-°F) whose walls are 9 ft high and 1 ft…

Q: What are is the maintenance procedure and safety to follow on the tirfor machine?

A: The Tirfor machine, also referred to as a hand winch or a pulling hoist, is an adaptable device used…

Q: A pump, geometrically similar to the 12.95-in model in Fig. P11.24, has a diameter of 24 in and is…

A: For water, ρ1 = 1.94 slug.ft3For gasoline, from Table A.3, ρ2 = 680 kg/m3 = 1.32 slug.ft3 From…

Q: 1. A thin pole of length L = 3 m and mass 6 kg is being raised by a rope of tension 80 Newtons as…

Q: Design an analog Butterworth filter with the following propertie Ap=2dB (Passband attenuation…

A: Butterworth filter of order N:H(s) = 1 / [(s^N) + (C1 * s^(N-1)) + (C2 * s^(N-2)) + ... + (C(N-1) *…

Q: W B A Y Fj FM

Q: How does the choice of material and cross-sectional geometry affect the bending behavior and…

A: In the field of mechanical engineering, the selection of materials and cross-sectional geometry of a…

Q: Calculate required torque applied to crank CF for static equilibrium. Calculate forcesA,B,C,D.

Q: You are asked to design an insulated stud timber wall and have the following materials available:…

A: Given:To find:Design a wall

Q: mercury Water flows at a flow rate of Q=5 lt/s from the system with diameters of d₁=60 mm and d₂=40…

A: This question is based on the concept of Bernoulli's equation. The assumptions are- Steady Flow: The…

Q: compute the maximum deflection of the beam Wu = 2.12 kip lft P₁ = 18.4 kips TR 10 ft = 27.008k…

A: The intensity of UDL, Wu = 2.12 kip/ftThe point load, Pu = 18.4 kips

Q: A uniform supersonic airstream travelling at a Mach number of 9.0 passes over a concave corner, as…

A: Mach number,M1=9.0shock angle,Assume,Deviation angle be

Q: Problem 1 1. Describe with the aid of diagrams the operational sequence of four stroke spark…

A: (a)Operational sequence of four stroke spark ignition engine(b)Efficiency of an ideal otto…

Q: Find the work done in pumping gasoline that weighs 42 pounds per cubic foot. The top of a…

Q: Consider the mechanism of Bar AB, Bar BC, and roller A. Roller A is constrained to move along the…

A: Consider the mechanism of Bar AB, Bar BC, and roller A. Roller A is constrained to move along the…

Q: A block of 50 kg is attached to a cable. The cable is then attached to a rotating assembly with a…

Q: A ship has a radius of gyration of k=8m, a transverse metacentric height GM of 2m and a displacement…

A: The radius of gyration, kxx = 8 mThe metacentric height, GM = 2 mThe displacement force, F = 156960…

Q: The elevator E and its freight have a total mass of 370 the 70-kg block c. If the motor has an…

Q: 1) The box is acted upon by two couples as shown in the figure. Calculate the magnitude and…

A: Given Figure

Q: How can the Bode plot be used to analyze and design control systems in mechanical engineering…

A: In control systems engineering, a Bode Plot is a graphical representation of a linear,…

Q: The vertical motion of mass A is defined by the relation x = cos(10 t) - 0.1sin(10t), where x and…

Q: A steam power plant is operating on the ideal Rankine cycle. The boiler is maintained at 4 MPa, and…

Q: a cylindrical tank 90 cm high and 60 cm in diameter, open to the atmosphere, initially completely…

Q: 100 mm A- 'В 200 mm, 3000 N 12 Q2. Determine the normal and shear stresses at point A and B. The…

A: The cross-section of the bar 12×12mmFind the state of stress at A and B

Q: 1 kg of a gas at a temperature of 40° C and a pressure of 120 KPa occupies a volume of 0.25m3. If…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: 1) Calculation of the torque on the shaft

VIEW

Step 3: 2) Calculation of the power of the shaft

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
Shaft length, L and a different allowable maximum shear stress, τmax and subject to a different Torque, T. For steel use a shear modulus, G=81,000 MPa. A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate: a) The minimum shaft diameter required. b) The angle of twist over the length of the shaft. c) The Power output if your shaft is rotating at 2000 rpm. L= 1.6m, τmax=100MPa , T=1.3kN-m
ach student has been allocated a different shaft length, L and a different allowable maximum shear stress,τmax and subject to a different Torque, T. For steel use a shear modulus, G=80,000 MPa.A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate:a) The minimum shaft diameter required.b) The angle of twist over the length of the shaft.c) The Power output if your shaft is rotating at 2000 rpm. L=1.9m τmax=95MPa T=1.5kN-m
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) Power transmission =60 kW,(ii) Shaft speed = 160 rpm,(iii)The angle of twist / m length = 1.1º(iv)Maximum twisting moment is 30% greater than its mean. (v) Take Modulus of rigidity as 105 Gpa. (i) Mean torque of the shaft (unit in Nm) = (ii)Maximum torque of shaft (unit in Nm) = (iii) The diameter of the shaft (unit in mm) = iv) Maximum shear stress in the shaft (Unit in MPa) is
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
A motor drives a shaft at 12 Hz and delivers 20 kW of power as shown in Fig.4. (a) If the shaft has a diameter of 30 mm, what is the maximum shear stress τmax in the shaft? (b) If the maximum allowable shear stress is 40 MPa, what is the minimum permissible diameter dmin of the shaft? A solid circular bar of diameter d = 50 mm is twisted in a testing machine until the applied torque reaches the value T = 500 Nm as shown in Fig.4. At this value of torque, a strain gage oriented at 45 ° to the axis of the bar gives a reading ε =339 ×10-6 . What is the shear modulus G of the material?
A torque of 40,000 N.m is applied to a 10 cm diameter shaft. What is the factor of safety of a steel(Sy = 410 MPa) if its shear strength is one-half of its capacity in tension?
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
Each student has been allocated a different shaft length, L and a different allowable maximum shear stress,τmax and subject to a different Torque, T. For steel use a shear modulus, G=80,000 MPa.A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate:a) The minimum shaft diameter required.b) The angle of twist over the length of the shaft.c) The Power output if your shaft is rotating at 2000 rpm. L=1.9m τmax=95MPa T=1.5kN-m
A shaft ABC rotates at 500rpm and is driven through a coupling at the end A. At B a pulley takes off two-third of the power, the remainder being absorbed at C. The part AB is 1.5m long and of 100mm diameter, BC is 2m long and of 75mm diameter. The maximum shear stress set up in BC is 40MPa. Determine the maximum stress in AB and the power transmitted by it, and calculate the total angle of twist in the length AC. Take G = 80GPa.
A) A cross section of a solid circular rod is subject to a torque of T = 3.6 kN⋅m. If the diameter of the rod is D = 8 cm , what is the maximum shear stress? B)The maximum stress in a section of a circular tube subject to a torque is τmax = 37 MPa . If the inner diameter is Di = 4.25 cm and the outer diameter is Do= 5.25 cm , what is the torque on the section?