Choose correct answer: In a hydraulic circuit,tank line is connected to D port of DCV.  Select one: True False

Q: Moving plate Pointer Fixed plate V The instrument type of the shown measu principle is: Select one:…

A: Electrodynamic Meter The electrodynamic ammeter uses a moving coil rotating in the field produced by…

Q: Design a pneumatic sequence valve circuit for clamp- and-drill devices as shown in Figure A2Q1. Give…

A: Given : To find: To draw a circuit to perform clamp and drill

Q: The common form of a variable area flowmeter is called _____. a. orifice plate b. venturi c.…

A: Rotameter and piston type are form of commom variable area flowmeter.Orific plate has more losses…

Q: In a venturimeter construction, the middle part is a known as short converging part. Select one:…

A:

Q: Identify the true statement from the following O Venturimeter is a rate of flow measuring instrument…

A: # Venturimeter is used for flow measuring not for Rate of flow so this statement wrong #venturimeter…

Q: g two (2) cylincer types:

A: 1. SINGLE ACTING CYLINDER 2.DOUBLE ACTING CYLINDER

Q: Controlling the rate of flow in a hydraulic circuit allows for speed control of hydraulic cylinders…

A: Controlling the rate of flow in a hydraulic circuit allows for speed control of hydraulic cylinders…

Q: Name the six basic components required in a hydraulic circuit.

A: Define : the six component required in a hydraulic circuit .

Q: Describe the general process used to calibrate a device such as a pressure gauge or a temperature…

A: Pressure guage is a mechanical instrument use to measure pressure of a fluid medium. General time of…

Q: The venturimeter is a discharge measuring instrument. Select one: O True O False

A: Venturimeter is a device works on the principal of Bernoulli theorem, used in measuring flow rate or…

Q: Vertical axis wind turbine is one which has blades rotating on an axis parallel to the ground…

A: The blades of a horizontal axis machine rotate on an axis parallel to the ground. The blades of a…

Q: one way flow control valve is the type of valve which is used to control the speed of an actuator.…

A:

Q: In a venturimeter construction, the entry part is known as short converging part. Select one: O True…

A: In a venturimeter, there are three main parts  - short converging parts (entry part) -throat (Middle…

Q: Accumulator that could be used in hydraulic system is _______________  type of accumulator.…

A:

Q: As fluids flow through pipes, energy is lost due to friction which produces a pressure differential.…

A: When a fluid flow through pipes, there is a loss of energy due to friction. Energy loss of fluid…

Q: 2. Answer the following table Types of Advantage Disadvantage Relation Formula Application…

A:

Q: Meter-out of pneumatic circuits utilizes check valve in only single direction. Select one: O True O…

A: We have to determine true/false

Q: Meter-out of hydraulic circuits utilizes flow control valve in only single direction.…

A: 2 way valve utilizes  flow control valve in only single direction and meter-out utilizes  flow…

Q: used to refer to the difference in pressure levels between two (unknown) pressure levels. Select the…

A: The difference between two unknown pressure levels is called differential pressure.

Q: A fixed rating pressure switch is adjusted inside the pressure control and display console to record…

A: Fixed rating pressure switch cannot be adjusted inside the pressure control because due to fixed…

Q: A pneumatic power system will usually have a return line  a. True b. False

A: Concept: 1) Pneumatic power system consists of some pneumatic valves, Electro-pneumatic valves,…

Q: The theoretical discharge is always greater than the actual discharge in the venturimeter. Select…

A: It is True

Q: 3/ Design the hydraulic circuit for any one hydraulic system application with working and neat…

A:

Q: weight vs spring different point plz

A: Weight is a force and spring is a mechanical element. The spring may be compressed or elongates but…

Q: Instruction: Complete the following table of Pneumatic Symbols. Name Symbol Name Symbol Compressor…

A: The complete table of Pneumatic symbols are shown in the following attached image:

Q: The compressor is used to increase the pressure of fluid-like air or grease. Select one: True False

A: Solution:

Q: The neutral point in a drill string can be defined as the point where the string changes from…

A: Answer is true. The neutral point in a drill is the point where there are neither compressive or…

Q: 1. Choice questions 1) The pressure of the hydraulic system is decided by ( a) Pressure of pump b)…

A:

Q: principle of instrument measurement

A: Measurement is defined as a process in which one converts physical parameters into meaningful…

Q: what would be the resistance of a circuit that is open

A: For an open circuit, no current will pass through the circuit.

Q: Which of the following is an example of fluid statics Water fall Water moving through a pipeline…

A: Fluid statics is the topic of fluid mechanics in which we study about the fluid at rest.

Q: Q) Sketch using symbols of hydraulic component Sequence valve to control the sequence between two…

A: pressure-controlled Sequence ValveThe operation of a typical pressure-controlled sequence valve is…

Q: 1- What are the similarities and differences between the drag line and the return line in the…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: coefficient of obstruction due to gate valve (only table please)

A: coefficient of obstruction (k) is used to measure the head loss due to valves and other fitting. It…

Q: What is the following systems, , where do they used, what is the specefication of such systems, what…

A: The engine is made composed of a stationary cylinder and a moving piston. As the gas expands in…

Q: A counter balance valve is not used for always flow retardation continuously, and resists its flow…

A: true

Q: Less staff is required for breakdown maintenance which is carried out as fast as possible to bring a…

A: Let us discuss breakdown maintenance.

Q: A compressor system which is controlled by starting-and-stopping is composed of a compressor with…

A: Introduction: The compressor compresses the gas fluid in order to raise its pressure. A pump and a…

Q: Select the plunger position in a Bellow sensor, for the condition that the outside pressure is lower…

A: Select the plunger position in a Bellow sensor, for the condition that the outside pressure is lower…

Q: 1. Design a Hydraulic circuit for the excavator earth moving equipment used in construction sites.

A: Design of hydraulic circuit

Q: Choose correct answer: In hydraulic system circuit,the pressure gauge would not be available in the…

A: Gauge pressure: It is the difference between the absolute pressure and atmospheric pressure.

Q: Circuit Diagram and Procedure

A:

Q: A fixed rating pressure switch is adjusted inside the pressure control and display console to record…

A: Pressure switch is a device, used to provide electrical feedback in response to measuring the level…

Q: The well with no planned deviation from vertical is called ___________ well a. deviated b.…

A: The well with no planned deviation from vertical is called

Q: Choose correct answer: ercury does not wet the wall of the tube of thermometer. Select one: True…

A:

Q: Q1/ in the below hydraulic system (circuit ?function), what does each symbol mean A G F В D E

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.