-coil is constructed by wrapping a wire of length 8.6 on a paper cylinder of adius 0.03 m and length 0.10 m. A current of 0.1 A is applied to coil. What s the expected value of the field at the center of the coil? Hint: determine ne number of turns of wire that fit the cylinder and determine the number f turns per unit of cylinder length. answer in microTesla (1 microTesla= 106 Tesla).

-coil is constructed by wrapping a wire of length 8.6 on a paper cylinder of adius 0.03 m and length 0.10 m. A current of 0.1 A is applied to coil. What s the expected value of the field at the center of the coil? Hint: determine ne number of turns of wire that fit the cylinder and determine the number f turns per unit of cylinder length. answer in microTesla (1 microTesla= 106 Tesla).

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter12: Sources Of Magnetic Fields

Section: Chapter Questions

Problem 64P: A solenoid with an iron core is 25 cm long and is wrapped with 100 turns of wire. When the current...

See similar textbooks

Similar questions

The flip coil of the preceding problem has a radius of 3.0 cm and is wound with 40 turns of copper wire. The total resistance of tire coil and ballistic galvanometer is 0.20 When the coil is flipped through 180° in a magnetic fielda change of 0.090 C flows through the ballistic galvanometer. (a) Assuming that and the face of the coil are initially perpendicular, what is tire magnetic field? (b) If the coil is flipped through 90°, what is tire reading of the galvanometer?
A flip coil is a relatively simple device used to measure a magnetic field, It consists of a circular coil of N turns wound with fine conducting wire. The coil is attached to a ballistic galvanometer, a device that measures the total charge that passes through it. The coil is placed in a magnetic field B such that its face is perpendicular to the field. It is then flipped through 180°, and tire total charge Q that flows through the galvanometer is measured. (a) If the total resistance of tire coil and galvanometer Is R, what is the relationship between B and Q? Because the coil is very small, you can assume that Bis uniform over it. (b) How can you determine whether or not tire magnetic field is perpendicular to the face of the coil?
A flat, square coil of 20 turns that has sides of length 15.0 cm is rotating in a magnetic field of strength 0.050 T. If tlie maximum emf produced in die coil is 30.0 mV, what is the angular velocity of the coil?
Unreasonable results Frustrated by the small Hall voltage obtained in blood flow measurements, a medical physicist decides to increase the applied magnetic field strength to get a 0.500-V output for blood moving at 30.0 cm/s in a 1.50-cm-diameter vessel. (a) What magnetic field strength is needed? (b) What is unreasonable about this result? (C) Which premise is responsible?
Consider the system pictured in Figure P28.26. A 15.0-cm horizontal wire of mass 15.0 g is placed between two thin, vertical conductors, and a uniform magnetic field acts perpendicular to the page. The wire is free to move vertically without friction on the two vertical conductors. When a 5.00-A current is directed as shown in the figure, the horizontal wire moves upward at constant velocity in the presence of gravity. (a) What forces act on the horizontal wire, and (b) under what condition is the wire able to move upward at constant velocity? (c) Find the magnitude and direction of the minimum magnetic Field required to move the wire at constant speed. (d) What happens if the magnetic field exceeds this minimum value? Figure P28.26
The density of charge carriers far copper is 8.471028 electrons per cubic meter. What will be the Hall voltage reading from a probe made up of 3cm2cm1cm ( (LWT) ) copper plate when a current of 1.5 A is passed through it in a magnetic field of 2.5 T perpendicular to the 3cm2cm .
The accompanying figure shows a metal disk of inner radius r1 and other radius r2 rotating at an angular velocity while in a uniform magnetic field directed parallel to the rotational axis. The brush leads of voltmeter are connected to the dark's inner and outer surfaces as shown. What is the reading of the voltmeter ?
A superconducting wire of diameter 0.25 cm carries a current of 1000 A. What is the magnetic field just outside the wire?
A 0.50-kg copper sheet drops through a uniform horizontal magnetic field of 1.5 T, and it reaches a terminal velocity of 2.0 m's. (a) What is the net map,-, eh: force on the sheet after it reaches terminal velocity? (b) Describe the mechanism responsible for this force, (c) How much power is dissipated as Joule heating while the sheet moves at terminal velocity?
A rectangular conducting loop is placed near a long wire carrying a current I as shown in Figure OQ23.5. If I decreases in time, what can be said of the current induced in the loop? (a) The direction of the current depends on the size of the loop. (b) The current is clockwise. (c) The current is counterclockwise. (d) The current is zero. (e) Nothing can be said about the current in the loop without more information.
A solenoid with an iron core is 25 cm long and is wrapped with 100 turns of wire. When the current through the solenoid is 10 A, the magnetic field inside it is 2.0 T. For this current, what is the permeability of the iron? If the current is turned off and then restored to 10 A, will the magnetic field necessarily return to 2.0 T?
A solenoid is wound with 2000 turns pet meter. When the cuiient is 5.2 A, what is the magnetic field within the solenoid?