Complete the leveling table given below for the sewer line AF. If an upward gradient of lin 20 starts at station (A) at a level of 100m above datum. Calculate the depth of excavation and the height of embankment at each station along the sewer line. Station B.M. A B C D E F Distance (m) 0 100 200 300 400 500 Staff Readings (m) I.S. F.S. B.S. 9.710 7.430 11.720 3.150 1.060 4.170 0.230 3.560 6.390 ΔΗ (m) Rise Fall R.L. (m) 103.620

Complete the leveling table given below for the sewer line AF. If an upward gradient of lin 20 starts at station (A) at a level of 100m above datum. Calculate the depth of excavation and the height of embankment at each station along the sewer line. Station B.M. A B C D E F Distance (m) 0 100 200 300 400 500 Staff Readings (m) I.S. F.S. B.S. 9.710 7.430 11.720 3.150 1.060 4.170 0.230 3.560 6.390 ΔΗ (m) Rise Fall R.L. (m) 103.620

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a triangular concrete-lined channel n=0.017 has a constant mild bed slope of 0.0015, side slopes of 1H:1V, and a normal flow depth of 2.60m. a sluice gate was installed along the triangular canal that immediately raised the flow depth 5m. perform the graphical method at an interval of 0.01m. start iterating at y=2.70m such that x=0, determine x at y=3.5m
Give me all right solutions with clear calculations. What should be the slope of a planed-timber flume, rectangular in cross-section, to carry 0.80 m³/ s. If the width is 1.2 m and the depth of flow is 0.45 m. Is the flow sub-critical or super-critical? Determine the critical depth and critical slope for the given discharge and width. Use n = 0.012
Water is to flow at a rate of 30m3/s in the concrete channel shown. Find the verticaldrop of the channel bottom per kilometer of length. n=0.012
A 2.0m diameter concrete pipe on a slope of 0.005 is to carry water at a normal depth of 1.5m. Determine the flow velocity and flow rate Take n=0.014 also determine q when ho=0.75 and h1=1.0m
A 28-in-diameter cast iron pipe on a 1/504 slope carries water at a depth of 8 in. as shown. What is the flow rate in ft3/s? Use n = 0.015.
Hydraulic gradient = 0.75 Lenght of H2 = 2.4m Critical hydraulic gradient Icr= 1.064
A semi-circular channel is made from brickwork (n = 0.013) and has a radius of1.524 m. If the channel slope is 0.002, determine the rate of discharge if thechannel is flowing full.
On a property, water is pumped from point A at the bottom of a hill to point B on top of the hill via a cast iron pipe at a flow rate of ?=Q= 0.06 ?3/?m3/s. The total pipe length is 173 ?m of diameter 0.14 ?m, and the elevation difference between A and B is 27 ?m. Between points A and B it is required to use 20 of the 90?90o flanged smooth bends (???=KLB= 0.19) and 5 of the fully open gate valve (???=KLG= 0.22). The entrance and exit losses are 0.54 and 1.3, respectively. Calculate the minimum pump power required to pump water from A to B, given that the pump efficiency is 0.76. Density and viscosity of water are 1000 ??/?3kg/m3 and 0.00131 ??/?.?kg/m.s, respectively.
*Hydraulics *Use handwritten A flow rate of 2.1 m^3/s is to be carried in an open channel at a velocity of 1.3 m/s. N=0.020. Determine the required slope if the channel is a semi circular section. Choices: A.) 0.00197 B.) 0.00781 C.) 0.00241 D.) 0.00167 E.) 0.00185 Determine the required slope if the channel is trapezoidal with depth equal to the width of the channel bottom and side slope of 1:1 Choices: A.) 0.00197 B.) 0.00781 C.) 0.00241 D.) 0.00167 E.) 0.00185
Three manholes MH1, MH2 and MH3 have been constructed along Platform 1 andPlatform 2 as shown in Figure 1. The reduced level of platform 1 is 23.500 m AOD andit was dropped 1.0 m downward to platform 2. The sewer is to be laid from MH1 toMH2 and MH2 to MH3 with a uniform gradient of 1 in 300 and 1 in 200 respectively. Thehorizontal distances from MH1 to MH2 and from MH2 to MH3 are 38.778 m and 88.312m respectively. The staff reading at TBM and invert level of MH1 were 1.366 and 2.768respectively.i) Determine the invert level of MH1, MH2, and MH3.ii) Calculate depth to be excavated at MH3.
A laboratory flume (n=0.012) is 10 in wide and set on a slope of 0.0003. With a measured flow of 0.1516cfs, the depth is observed to vary between 0.361 and 0.366 ft. Classify the water-surface profile. Show all necessary calculations, and sketch the profile
or the channel cross section of Fig. X10.3.6, a = 1 m, b = 3 m, d = 2 m, w = 8 m, and n = 0.015. What bed slope is required so that the flow will be 16 m3/s when the depth of flow is 1.50 m?