ComputationA house has the following specifications for a circuit determine the size of the circuit breaker, wire and size of pipe to be used for each circuit and the service entrance. show computation and tabulate final answer, 1. 15 lighting outlets 2. 1 kitchen range 3. 12 lighting outlets 4. 1 water heater at 1500 watts 5. 12 convenience outlet 6. 8 convenience outlet 7. 9 convenience outlet 8. 12 lighting outlet 9. 3 convenience outlet 10. spare-1500 watts 11. spare- 1500 watts

ComputationA house has the following specifications for a circuit determine the size of the circuit breaker, wire and size of pipe to be used for each circuit and the service entrance. show computation and tabulate final answer, 1. 15 lighting outlets 2. 1 kitchen range 3. 12 lighting outlets 4. 1 water heater at 1500 watts 5. 12 convenience outlet 6. 8 convenience outlet 7. 9 convenience outlet 8. 12 lighting outlet 9. 3 convenience outlet 10. spare-1500 watts 11. spare- 1500 watts

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter8: Lighting Branch Circuit For The Front Bedroom

Section: Chapter Questions

Problem 5R: For residential wiring, not less than one 15-ampere lighting branch circuit should be provided for...

See similar textbooks

Similar questions

17.b. Which of the following is the best example of a building supplied by a single branch circuit?A. A detached carport with no doors, walls, or windowsB. A detached garage at a dwelling occupancyC. A ground-mounted air conditionerD. A university dormitory
6.a. The amount of short-circuit current that flows depends upon the amperes available at the source ofpower, the length of the circuit, and what other primary factor?A. The presence of a ground fault currentB. Proper installation of the branch circuitC. Presence of no previous damage to the electrical systemD. The size of the conductors and voltage at which they operate6.b. You're evaluating the components of a multioccupancy building that won't have an on-site employee. Tobe compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water-pump disconnect.
The only way to reach any of the levels where ABC Company is located in a building with ten stories is to use the elevator. In addition, those on the ninth and tenth levels need to connect to a group of servers located on the eighth. Describe the best wiring for the lift shaft. Pick the best option if there is more than one and justify your decision. If you think that interfloor connections may need to operate at substantially greater rates in the future, you may want to reconsider your current option. What is the optimum media for unbounded data transfer requirements? Justify your response.
when calculating a dwelling lighting load on the "volt-ampere per ft2" basis, the receptacle load used for floor lamps, table lamps, and so fourth
A homeowner wants to add 12 general-purpose receptacle outlets to the electrical drawings before the house is built, what additional load, in volt-amperes will they add to the service load calculation?
In the past, it was common practice to connect the lighting and receptacle(s) in a bathroom to the same circuit. Because of overloads caused by high-wattage grooming appliances, the Code now requires that these receptacle(s) be supplied by a separate 20-ampere branch circuit. Where in the Code is this requirement found? NEC __________
Approximately how many feet (meters) of 2-wire cable and 3-wire cable are needed to complete the circuit supplying the Master Bedroom? Two-wire cable: ___________ ft (___________ m). Three-wire cable: ___________ ft (___________ m).
13.B. The amount of fault current that bonding connections have to endure is related to which of thefollowing?A. The quality of the fittings that were chosen for the systemB. The amount of available fault current delivered by the system or utilityC. The type of equipment and the location in the systemD. The number of connections that are part of the listed assembly13.C. What is the most common grounding electrode used to connect utility service equipment to Earth?A. Ground rodB. PipeC. PlateD. Ground ring
10.a. Which of the following is a condition of the exception that allows the grounded conductor of feeders tobe used for grounding at separate buildings or structures?A. There are common electrically continuous metallic paths between the feeder source and the destination at the structure served.B. There are common electrically continuous nonmetallic paths between the equipment grounding conductor and the destinationat the structure served.C. An equipment grounding conductor isn't included with the supply circuit to the separate structure.D. Ground-fault protection of equipment is provided on the supply side of the feeder.10.b. A service disconnection means must be installed adjacent to, within sight of, and no more than_______ feet from a mobile home.A. 20B. 30C. 10D. 50
14. The amount of fault current that bonding connections have to endure is related to which of thefollowing?A. The quality of the fittings that were chosen for the systemB. The amount of available fault current delivered by the system or utilityC. The type of equipment and the location in the systemD. The number of connections that are part of the listed assembly
Question 8.aWhich article of the NEC describes the proper placement of outlets inthis type of room? Also, based on the given load what type of outlets areneeded for this room? Question 8.bPart 1: According to the NEC. What's the minimum highallowed for each outlet?Part 2: What are the best locations to install the outlets?Part 3: How many feet an outlet should be located at the wallfrom the floor, used to power a light fixture?
The frames of ranges, wall-mounted ovens, counter-mounted cooking units, and clothes dryers under the conditions permitted for existing installations, ___ permitted to be connected to the grounded circuit conductor. Select one: a. shall not be b. can not c. may be d. shall be