19 Moving to another question will save this response.Question 19Compute for the current i3 in the circuit shown below.O-512.9877 mAO-513.2365 mAO-512.6050 mAO-513.0145 mAab-r15 OhmsV1www=15 Vr23 Ohmsi2V2믐8 VR_LOAD10 Ohmsr33 Ohmsi3V믐3 V

r1 = 5 ohr2 = 3 ohm r3 = 3 ohmV1 = 15 V V2 = 8 V V3 = 3 V Rload = 10 ohm

Compute for the current i3 in the circuit shown below. ○ -512.9877 mA ⓒ-513.2365 mA ⓒ-512,6050 mA ○-513.0145 mA b r1 5 Ohms V1 픔 15 V .r2 3 Ohms Tiz V2 믐 BV R_LOAD ww 10 Ohms r3 3 Ohms 13 믐 3V

Compute for the current i3 in the circuit shown below. ○ -512.9877 mA ⓒ-513.2365 mA ⓒ-512,6050 mA ○-513.0145 mA b r1 5 Ohms V1 픔 15 V .r2 3 Ohms Tiz V2 믐 BV R_LOAD ww 10 Ohms r3 3 Ohms 13 믐 3V

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter18: Direct-Current Circuits

Section: Chapter Questions

Problem 11P: Consider the circuit shown in Figure P18.11. Find (a) the potential difference between points a and...

See similar textbooks

Similar questions

When resistors with different resistances are connected in parallel, which of the following must be the same for each resistor? Choose all correct answers, (a) potential difference (b) current (c) power delivered (d) charge entering each resistor in a given time interval (e) none of those answers
Three identical 60.0-W, 120-V lightbulbs are connected across a 120-V power source as shown in Figure P28.72. Assuming the resistance of each lightbulb is constant (even though in reality the resistance might increase markedly with current), find (a) the total power supplied by the power source and (b) the potential difference across each lightbulb.
When resistors with different resistances are connected in series, which of the following must be the same for each resistor? Choose all correct answers, (a) potential difference (b) current (c) power delivered (d) charge entering each resistor in a given lime interval (e) none of those answers
The circuit in Figure P27.34a consists of three resistors and one battery with no internal resistance. (a) Find the current in the 5.00- resistor. (b) Find the power delivered to the 5.00- resistor. (c) In each of the circuits in Figures P27.34b, P27.34c, and P27.34d, an additional 15.0-V battery has been inserted into the circuit. Which diagram or diagrams represent a circuit that requires the use of Kirchhoffs rules to find the currents? Explain why. (d) In which of these three new circuits is the smallest amount of power delivered to the 10.0- resistor? (You need not calculate the power in each circuit if you explain your answer.) Figure P27.34
The following statements are related to household circuits and electrical safety. Determine whether each statement is true (T) or false (F). (a) Circuit breakers are wired in series with the outlets they protect. (b) A circuit breaker rated at 20 A provides a constant current of 20 A to each outlet in the circuit. (c) Three-wire electrical cords help prevent dangerous electrical shocks by grounding the case of a device.
Consider the circuit shown in Figure P18.10. (a) Calculate the equivalent resistance of the 10.0- and 5.00- resistors connected in parallel. (b) Using the result of part (a), calculate the combined resistance of the 10.0-, 5.00-, and 4.00- resistors. (c) Calculate the equivalent resistance of the combined resistance found in part (b) and the parallel 3.00- resistor. (d) Combine the equivalent resistance found in part (c) with the 2.00- resistor. (e) Calculate the total current in the circuit. (f) What is the voltage drop across the 2.00- resistor? (g) Subtracting the result of part (f) from the battery voltage, find the voltage across the 3.00- resistor. (h) Calculate the current in the 3.00- resistor. Figure P18.10
An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V battery with a 0.0100- internal resistance, (a) What is the current to the motor? (b) What voltage is applied to it? (c) What power is supplied to the motor? (d) Repeat these calculations for when the battery connections are corroded and add 0.0900 to the circuit. (Significant problems are caused by even small amounts of unwanted resistance in low-voltage, high-current applications.)
Using an ohmmeter, a student measures the resistance between various points on his body. He finds that the resistance between two points on the same finger is about the same as the resistance between two points on opposite hands-both are several hundred thousand ohms. Furthermore, the resistance decreases when more skin is brought into contact with the probes of the ohmmeter. Finally, there is a dramatic drop in resistance (to a few thousand ohms) when the skin is wet. Explain these observations and their implications regarding skin and internal resistance of the human body.
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
The following statements are related to household circuits and electrical safety. Determine whether each statement is true (T) or false (F). (a) Circuit breakers are wired in series with the outlets they protect. (b) A circuit breaker rated at 20 A provides a constant current of 20 A to each outlet in the circuit. (c) Three-wire electrical cords help prevent dangerous electrical shocks by grounding the case of a device.
A 0.0200- ammeter is placed in series with a 10.00- resistor in a circuit, (a) Draw a circuit diagram of the connection, (b) Calculate the resistance of the combination, (c) If the voltage is kept the same across the combination as it was through the 10.00- resistor alone, what is the percent decrease in current? (d) If the current is kept the same through the combination as it was through the 10.00-resistor alone, what is the percent increase in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
Consider the circuit shown in Figure P18.11. Find (a) the potential difference between points a and b and (b) the current in the 20.0- resistor. Figure P18.11