1. DREZ Inc. has three departments, each of which houses variety of manufacturing equipment.One department has six machines listed in the table.Note: Add 10 feet each side of the first two machines types and 8 feet to the others to allow foroperators access, material handling carrier access and work-in process storage.Machine TypeHobbingLength(ft)Width(ft)No. of machines1051Punch Press10101Extruding Equipment20102Injection Molding10103Surface Finishing554Debburing10102Compute the total space requirement of the cell considering the following assumptions for eachequipment type:a. Auxiliary space requirement is 10% of those machine areab. Operator space is 8% of the required of the auxiliary and machine spaceС.Material storage is 20% of the actual area required for machinesd. Additional allowance is 80% of the areas determined in a b.c and machine area.

Answered: Compute the total space requirement of…

Engineering

Mechanical Engineering

Compute the total space requirement of the cell considering the following assumptions for each equipment type:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A worker is currently responsible for tending two machines in a machine cluster. The service time per machine is 0.35 min and the time to walk between machines is 0.15 min.The machine automatic cycle time is 1.90 min. If the worker’s hourly rate = $12/hr andthe hourly rate for each machine = $18/hr, determine (a) the current hourly rate for thecluster, and (b) the current cost per unit of product, given that two units are produced byeach machine during each machine cycle. (c) What is the percent idle time of the worker?(d) What is the optimum number of machines that should be used in the machine cluster, ifminimum cost per unit of product is the decision criterion?
Q1: Explain the significant role of Power and Free Conveyor Systems in modern manufacturing facilities. In your opinion, how the mode of control of power industrial trucks helps to handle the materials in different ways.
Operations processes are known to differ in terms of volume of their output. Explain thecharacteristics of high volume operations.
Four machines used to produce a family of parts are to be arranged into a GT cell.The from-to data for the parts processed by the machines are shown in the table below.(a) Determine the most logical sequence of machines for this data. (b) Construct the network diagram for the data, showing where and how many parts enter and exit the system.(c) Compute the percentages of in-sequence moves, bypassing moves, and backtrackingmoves in the solution. (d) Develop a feasible layout plan for the cell
Q. Discuss different types of Layout planning in manufacturing unit with example.
I need help with part a b and c in question 2. Question one is listed because it is referenced in question 2. Any help with question 2 would be appreciated even if it is not all 3 parts. thank you 1. A certain batch of parts is routed through six machines in a batch production plant. The setup and operation times for each machine are given in the table below. Batch size is 200 and the average nonoperation time per machine is15 hr. Determine (a) manufacturing lead time and (b) hourly production rate for operation 4.Machine 1 2 3 4 5 6Setup time (hr) 5 3 6 4 5 3Operation time (min) 3.0 3.3 8.2 3.9 4.5 2.3 a. 6(4.3+200(3.9/60)+15) = 193.8 hours 24.2 days if 8 hour shiftb. 4(60)+200(3.9)/200 =5.1 hourly production for operation 4 2. Suppose the part in the previous problem is made in very large quantities on a production line in which an automated work handling system is used to transfer parts between machines. Transfer time between stations is 30 sec. total time required to…
1- Consider the precedence relationship between the activities of an assembly line. Knowing that the cycle time (T) of the assembly line is 10, then: a) Show how the activities are assigned to the work station? b) Calculate line efficiency and smoothness indices.
An AS/RS is used for work-in-process storage in a manufacturing facility. The AS/RS has five aisles, each aisle being 120 ft long and 40 ft high. The horizontal and vertical speeds of the S/R machine are 400 ft/min and 50 ft/min, respectively. The S/R machine requires 12 sec to accomplish a pick-and-deposit operation. The number of single-command cycles equals the number of dual-command cycles. If the requirement is that the AS/RS must have a throughput rate of 200 S/R transactions/hr during periods of peak activity, will the AS/RS satisfy this requirement? If so, what is the utilization of the AS/RS during peak hours?
Subject: Manufacturing Processes Please do all parts
A CNC milling machine has a purchase price of £120,000 and it is considered from an accounting standpoint to be depreciated to zero value over a period of 5 years. If the machine is to be used for 2 shifts with each shift working for 37 hours/ week and 45 weeks/ year. What is the machine cost/ hr which must be charged in order to amortise/repay the costs over the 5 year period? To make the calculation simpler, you can assume that over the 5 year period you will be required to pay back 8% interest on the sum borrowed. Express your answer in § / hour rounded up to the nearest penny
A very special manufacturing operation is being designed as an assembly line. Table 1 shows the tasks that need to be performed, their task time, and preceding tasks. The goal is to produce 5760 products per month. The company has an operation pattern of 24 days per month with 8 hours per day. Draw a precedence diagram. Determine the cycle time. Using the largest work element-time rule, assign tasks to the workstations in order to have appropriate line balancing. Identify the idle time for workstation 1, 2 and 6. Identify the number of workstations for the balanced line. Calculate the balanced line effieciency to 2 decimal places (Example 0.78).
A machine makes two components; call them types A and B. It takes 250 seconds to switch production between the component types. During that time, no production occurs. When in production, each unit of A or B requires 0.5 second to be completed. The two components, A and B, are combined in an assembly process to make a final product; call it C. The assembly step can combine the two components into 1 unit every 2 seconds, or 30 units per minute. Assume there is ample demand. Suppose the machine rotates between one batch of 1,000 units of A and 1,000 units of B. What is the average inventory of B components? answer:______units