Consider 1.0 kg of a 99.4 wt% Fe-0.6 wt% C alloy that is cooled to a temperature just below the eutectoid. How many kilograms of proeutectoid ferrite form? How many kilograms of eutectoid ferrite form? How many kilograms of cementite form? Show your work. Note: At the eutectoid temperature, ferrite concentration is at 0.022 wt% C. The eutectoid point is at 0.76 wt% C.

Consider 1.0 kg of a 99.4 wt% Fe-0.6 wt% C alloy that is cooled to a temperature just below the eutectoid. How many kilograms of proeutectoid ferrite form? How many kilograms of eutectoid ferrite form? How many kilograms of cementite form? Show your work. Note: At the eutectoid temperature, ferrite concentration is at 0.022 wt% C. The eutectoid point is at 0.76 wt% C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An alloy of 30 wt % Pb and 70 wt % Sn is slowly cooled from 250°C to 27°C: d) What is the amount and composition of each phase that is present at 183°C - ∆T ? e) What are the amounts of each phase present at room temperature? f) Draw the microstructure 183°C + ∆T and 183°C - ∆T in 2 cm diameter circle.
Please do it as early as possible. Name the microstructural products of a eutectoid iron-carbon alloy (0.76 wt% C ) that is first completely transformed to austenite and then cooled to room temperature at a rate of 100 °C/s
A 50 wt% Pb–50 wt% Mg alloy is slowly cooled from 700°C to 400°C. (a) At what temperature does the first solid phase form? (b) What is the composition of this solid phase? (c) At what temperature does the liquid solidify? (d) What is the composition of this last remaining liquid phase?
A 80%Sn-20%Pb alloy is melted fully at 300°C and then slowly cooled down to 182°C. Sketch the microstructures at 300°C, 200°C, and 182°C, respectively. Label all phases and indicate their approximate compositions. Also, determine the follows for this alloy at 182°C. (1) The weight fractions of α and β phases.(2) The weight fractions of primary β and eutectic structure.(3) The weight fraction of eutectic β .
The magnesium-lead alloy was cooled from 600°C to 450°C. Microstructures are composed of initial Mg2Pb and process microstructures factors. Find the composition of this alloy if the weight fraction of the microorganism factor is 0.28.
The ratio of eutectoid cementite in the iron-carbon alloy is 0.104. Can the carbon content of this alloy be determined based on this information? If not, please explain why:
Given that a component is made of 0.1 wt.%C steel is carburized by introducing 1.0 wt.% carbon at its surface at 980ºC. Calculate the carbon content at 0.5 mm below the surface of this component after 1 hour.Do= 0.2 cm^2/s and Qd=40,000 cal/mol.
Using the following table, draw a melting point diagram and estimate the eutectic temperature and composition: Percent composition Melting point range (°C) 100% A 125-126 75% A-25% B 115-120 65% A- 35% B 128-131 50% A- 50% B 135-140 100% B 151-152 Can you suggest what additional points you need to give a more accurate measure of the eutectic point?
Determine the fraction of eutectoid cementite with 0.84 wt.% C in the iron-carbon alloy.
For a 50-50 Mg-Pb alloy, what would the percent of each phase be at 500°C, 300°C and 100°C?
Is it possible to have a copper–zinc alloy that, at equilibrium, consists of an  phase of composition 75 wt% Zn– 25 wt% Cu, and also a liquid phase of composition 90 wt% Zn and 10 wt% Cu? If so, what will be the approximate temperature of the alloy? If this is not possible, explain why.
The Iron-Carbon system: Phase Diagram 1. You heat treated a 1045 steel plate by heating it to 900°C and slowly cooling it to 725 °C, which is below the eutectoid temperature. What phases are present at 725°C? What are the compositions of each phase at 725°C? What are the weight fractions of each phase at 725°C? What microconstituents are present at 725°C? What are the compositions of each microconstituent at 725°C? What are the weight fractions of each microconstituent at 725°C?