Consider a flow of water in a cylinder maintained at constant temperature of 1000 C, the diameter of the cylinder is 50 mm and the length of the tube is 6m. The inlet and the outlet temperature of the water is Ti = 150 C and T0 = 570 C . Find the average heat transfer coefficient associated with the flow of water . Mass flow rate is 0.25 Kg/ s and Cp = 4.178 KJ/Kg.K

Consider a flow of water in a cylinder maintained at constant temperature of 1000 C, the diameter of the cylinder is 50 mm and the length of the tube is 6m. The inlet and the outlet temperature of the water is Ti = 150 C and T0 = 570 C . Find the average heat transfer coefficient associated with the flow of water . Mass flow rate is 0.25 Kg/ s and Cp = 4.178 KJ/Kg.K

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Similar questions

Consider a flow of water in a cylinder maintained at a constant temperature of 1000 C, the diameter of the cylinder is 50 mm and the length of the tube is 6m. The inlet and the outlet temperature of the water are Ti = 150 C and T0 = 570 C . Find the average heat transfer coefficient associated with the flow of water. Mass flow rate is 0.25 Kg/ s and Cp = 4.178 KJ/Kg.K
Consider a flow of water in a cylinder maintained at constant temperature of 1000 C, the diameter of the cylinder is 50 mm and the length of the tube is 6m. The inlet and the outlet temperature of the water is Ti = 150 C and T0 = 570 C . Find the average heat transfer coefficient associated with the flow of water . Mass flow rate is 0.25 Kg/ s and Cp = 4.178 KJ/Kg.K A) 850 W/m2.K B) 650 W/m2.K C) 755 W/m2.K D) 725 W/m2.K
Assuming Reynolds analogy applies, estimate the heat transfer coefficient in BTU/hr-ft2-°F, for water flowing inside a 2.0 in. ID smooth horizontal straight pipe at a velocity of 4 fps and an average temperature of 78°F.a. 1790 b. 2000 c. 2910 d. 2240
Determine the mass flow rate (kg/s) of water that must flow through a conduit to carry 15,000 kJ/s of heat energy if the temperature difference is 10 degrees Celsius. Cp water=4.186 k*J/Kg*K
A household radiator has an inlet temperature of 73.2 oC and an outlet temperature of 42.5 oC. The water flows through the radiator at a steady rate of 1×10-5 m3 s-1 and the radiator has reached a steady temperature. Given that the density of water is 1000 kg m-3 and its specific heat capacity is 4200 J kg-1 K-1, calculate the rate of heat loss (in W or J s-1) from the radiator.
Aroomiscooledbycirculatingchilledwaterthroughaheatexchangerlocatedin a room. The air is circulated through the heat exchanger by a 0.25-hp (shaft output) fan. Typical efficiency of small electric motors driving 0.25-hp equipment is 54 percent. Determine the rate of heat supply by the fan–motor assembly to the room.
Water enters a 2.5-cm-internal-diameter thin copper tube of a heat exchanger at 15oC at a rate of 0.61 kg/s, and is heated by steam condensing outside at 115oC. If the average heat transfer coefficient is 950 W/m2.K, determine the length of the tube required in order to heat the water to 109oC. (Insert answer for Q (kW), TLMTD (oC) and L (m) )
Solve the problem. In a steady flow apparatus, 135 kJ of work is done by each kg of fluid. The specific volume of the fluid, pressure, and speed at the inlet are 0.37 m3/kg, 600 kPa and 16 m/s. The inlet is 32 m above the floor, and the discharge pipe is at floor level. The discharge conditions are 0.62 m3/kg, 100 kPa and 270 m/s.. The total heat loss between the inlet and discharge is 9 kJ/kg of fluid. In flowing through this apparatus, does the specific internal energy increase or decrease, and by how much?
Water flows through two adiabatic turbines and a heat exchanger as shown in the picture. Hot air is used to provide additional energy to the water between the two turbines. The first turbine has a power output of 8,000 kW. Determine the power output of the second turbine in kW and the process efficiency of each turbine. Determine the state of steam in turbine 1, Formulate the 1st Law for turbine 1, and solve for the flow rate of steam. Formulate the 1st Law for the heat exchanger, and solve for the temperature at exit
Water (cp = 4182 J/Kg.K) at a flow rate of 5000 Kg/hr is heated from 10oC to 35oC in an oil cooler by engine oil (cp = 2072 J/Kg.K) with an inlet temperatureof 85oC and a flow rate of 6000 Kg/hr. Take the overall heat transfer coefficient to be 3500 W/m2.K. What are the areas required for:a. Parallel Flow.b. Counter Flow
In a hydroelectric power plant, 100 m3/s of water flows from an elevation of 120 m to a turbine, where electric power is generated . The total irreversible head loss in the piping system from point 1 to point 2 (excluding the turbine unit) is determined to be 35 m. If the overall efficiency of the turbine–generator is 80 percent, estimate the electric power output.
3. The food storage room requires a cooling system with a capacity of 15 tons of refrigeration that operates at an evaporator temperature of -17.5 ° C and a condenser temperature of 42.5 ° C. The refrigerant used is R-134a and the system operates in saturated conditions. a. COP = Answer . b. Refrigerant flow rate = Answer kg / s. c. Heat loss rate in condenser = Answer kJ / s.