Consider a large 5-cm-thick brass plate (k = 111 W/m · °C) in which heat is generated uniformly at a rate of 2 x 105 W/m3. One side of the plate is insulated while the other side is exposed to an environment at 25°C with a heat transfer coefficient of 44 W/m2. °C. Explain where in the plate the highest and the lowest temperatures will occur, and determine their value

Consider a large 5-cm-thick brass plate (k = 111 W/m · °C) in which heat is generated uniformly at a rate of 2 x 105 W/m3. One side of the plate is insulated while the other side is exposed to an environment at 25°C with a heat transfer coefficient of 44 W/m2. °C. Explain where in the plate the highest and the lowest temperatures will occur, and determine their value

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a meat processing plant, 2-cm-thick steaks (k =0.45 W/m·K and a = 0.91 * 1027 m2/s) that are initially at25°C are to be cooled by passing them through a refrigerationroom at 211°C. The heat transfer coefficient on both sides ofthe steaks is 9 W/m2·K. If both surfaces of the steaks are to becooled to 2°C, determine how long the steaks should be keptin the refrigeration room. Solve this problem using analyticalone-term approximation method (not the Heisler charts).
A hot water pipe at 80°C is losing heat to the surrounding air at 5°C by natural convection with a convection heat transfer coefficient of 25 W/ m2.°C. The rate of heat loss from the pipe by convection is to be determined.
Does a heat engine that has a thermal efficiency of 100 percent necessarily violate the second law of thermodynamics? Explain.
A 5-cm-external-diameter, 10-m-long hot water pipe at 80°C is losing heat to the surrounding air at 5°C by natural convection at a rate of 1175 W. Determine the rate at which the work potential is wasted during this process as a result of this heat loss.
A building with an internal volume of 400 m3 is to be heated by a 30-kW electric resistance heater placed in the duct inside the building. Initially, the air in the building is at 14°C, and the local atmospheric pressure is 95 kPa. The building is losing heat to the surroundings at a steady rate of 450 kJ/min. Air is forced to flow through the duct and the heater steadily by a 250-W fan, and it experiences a temperature rise of 5°C each time it passes through the duct, which may be assumed to be adiabatic. How long will it take for the air inside the building to reach an average temperature of 24°C?
A building with an internal volume of 400 m3 is to be heated by a 30-kW electric resistance heater placed in the duct inside the building. Initially, the air in the building is at 14°C, and the local atmospheric pressure is 95 kPa. The building is losing heat to the surroundings at a steady rate of 450 kJ/min. Air is forced to flow through the duct and the heater steadily by a 250-W fan, and it experiences a temperature rise of 5°C each time it passes through the duct, which may be assumed to be adiabatic. Determine the average mass flow rate of air through the duct.
Heat is transferred steadily through a 0.2-m-thick, 8 m × 4 m wall at a rate of 2.4 kW. The inner and outer surface temperatures of the wall are measured to be 15°C and 5°C. The average thermal conductivity of the wall is (a) 0.002 W/m·°C (b) 0.75 W/m·°C (c) 1.0 W/m·°C (d) 1.5 W/m·°C (e) 3.0 W/m·°C
Consider the process of baking potatoes in a conventional oven. Can the hot air in the oven be treated as a thermal energy reservoir? Explain.
Consider a large 3-cm-thick stainless steel plate in which heat is generated uniformly at a rate eg of 6 x 106 W/m3. Assuming the plate is losing heat from both sides, determine the heat flux on the surface of the plate during steady operation in kW/m2.
A cylindrical fuel rod (k = 30 W/m•K) of 2 cm in diameter is encased in a concentric tube and cooled by water. The fuel rod generates heat uniformly at a rate of 100 MW/m3, and the average temperature of the cooling water is 115°C with a convection heat transfer coefficient of 2500 W/m2.k. The operating pressure of the cooling water is such that the surface temperature of the fuel rod must be kept below 200°C to avoid the cooling water from reaching the critical heat flux (CHF). The critical heat flux is a thermal limit at which a boiling crisis can occur Determine the temperature at the surface of the rod. What can you do to lower the temperature aty the surface?
A long roll of 2-m-wide and 0.5-cm-thick 1-Mn manganesesteel plate (ρ = 7854 kg/m3 and cp = 0.434 kJ/kg·°C)coming off a furnace at 820°C is to be quenched in an oil bathat 45°C to a temperature of 51.1°C. If the metal sheet is movingat a steady velocity of 10 m/min, determine the requiredrate of heat removal from the oil to keep its temperature constantat 45°C.
A student living in a 4-m x 6-m x 6-m dormitory room turns on her 150-W fan before she leaves the room on a summer day, hoping that the room will be cooler when she comes back in the evening. Assuming all the doors and windows are tightly closed and disregarding any heat transfer through the walls and the windows, determine the temperature in the room when she comes back 10 h later. Use specific heat values at room temperature, and assume the room to be at 100 kPa and 15°C in the morning when she leaves.