H.W. Q: An aluminum pan whose thermal conductivity is 237 W/m-°C has a flat bottom with diameter 20 cm and thickness 0.4 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 800 W. If the inner surface of the bottom of the pan is at 105°C, determine the temperature of the outer surface of the bottom of the pan. 105°C 0.4 cm Answer: T= 105.43 °C 800 W

H.W. Q: An aluminum pan whose thermal conductivity is 237 W/m-°C has a flat bottom with diameter 20 cm and thickness 0.4 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 800 W. If the inner surface of the bottom of the pan is at 105°C, determine the temperature of the outer surface of the bottom of the pan. 105°C 0.4 cm Answer: T= 105.43 °C 800 W

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.64P

See similar textbooks

Similar questions

Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat 100°C; Properties of water at 100°C: Density. pl= 961 kg/m3; Kinematic viscosity, v 0.293x10-6 m2/s: Prandti Number. Pr 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, u = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg; pv = 0.597 kg/m3; a = 0.0588 N/m; Csf=0.013; n=1:
Example 9: A 2-kW resistance heater wire whose thermal conductivity is k = 15 W/m ·°C has a diameter of D = 4 mm and a length of L = 0.5 m, and is used to boil water. If the outer surface temperature of the resistance wire is Ts = 105°C, determine the temperature at the center of the wire.
The temperature on the two surfaces of a 25mm thick steel plate (k=48w/m°c)
A Gasoline engine operating on an air standard condition has a clearance volume of 15cm3 and a displacement volume of 100cm3 . Determine the theoretical thermal efficiency of the engine.
Most automobiles have a coolant reservoir to catch radiator fluid that may overflow when the engine is hot. Such a radiator, made of copper, is filled to its 12-L capacity when at 10.0°C. -What volume of radiator fluid, in liters, will overflow when the radiator and fluid reach their 99.5°C operating temperature, given that the fluid’s thermal coefficient of volume expansion is 400.0 × 10-6 / °C? The coefficient of volume expansion for copper is 5.1 × 10-5 /°C.
350 pipes are fixed as square in a pipe bundle used for condenser. PipeThe outer diameters are 8 mm and the steam at 0.2 bar is desired to be condensed on the pipes. pipe outer The surface temperature is kept constant at 30 °C. If the length of the pipes is 1.5 m, the heat transferred in the systemCalculate the amount of energy and the amount of condensed steam
A copper rod whose diameter is 2 cm and length 50 cm have one end in boiling water, the other end in a jacket cooled by flowing water which enters at 10oC. The thermal conductivity of the copper is 0.102 kCal/m-soC. If 0.20 kg of water flows through the jacket is 6 min, by how much does the temperature of the water increase?
The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is increased by a gearbox that has an efficiency of 0.93. In turn, the gearbox output shaft drives an electric generator with an efficiency of 0.95. The cylindrical nacelle, which houses the gearbox, generator, and associated equipment, is of length L = 6 m and diameter D = 3 m. If the turbine produces P = 2.5 MW of electrical power, and the air and surroundings temperatures are T = 25 oC and Tsur = 20 oC, respectively, determine the minimum possible operating temperature inside the nacelle. The emissivity of the nacelle is 0.83, and the convective heat transfer coefficient is h = 35 W/m2 .K. The surface of the nacelle that is adjacent to the blade hub can be considered to be adiabatic, and solar irradiation may be neglected. Use Fin or N number of fins to reduce the Ts of the nacelle less than 143 oC
An electric windshield defroster is used to remove 0.25-in of ice from a windshield. The properties of the ice are Tsat = 328F, uif = hif = 144 Btu/lbm, and v = 0.01602 ft3/lbm. Determine the electrical energy required per square foot of windshield surface area to melt this ice and remove it as liquid water at 328F. What is the minimum temperature at which the defroster may be operated? Assume that no heat is transferred from the defroster or ice to the surroundings.
Q2 : Room walls are composed of common bricks and outside and inside plaster layers with an overall heat transfer coefficient of 2.5 W / m² ° C . The outside air temperature is 15 ° C ( DBT ) and the inside design conditions are 23 ° C DBT , 55 % RH . Is condensation occur on the inside surface or not ? Take f = 8.26 W / m² ° C . SHI
A cylindrical vessel (D=98,4 cm) is filled with water (ρ=1000 kg/m3, c=4.187 kJ/kg.K) to a depth of 113,64 cm. The initial temperature of the water is 15°C. Determine the time [min] required to increase the water temperature to 50°C when it is immersed into tank, filled with oil at 105°C. (NOTE: The overall heat transfer coefficient between the oil and the water is 284 W/m2.K. The surface area is 4.2 m2.)