Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontaland vertical planes at the point are S, = 8.0 ksi, S, = 10.5 ksi, and Sxy = 8.0 ksi.(a) Determine the principal stresses and the maximum in-plane shear stress acting at the point.(b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)(c) Compute the absolute shear stress at the point.SySxyS.

Answered: Image /qna-images/answer/cfa3bc51-db1e-479c-b098-f6d56c73d0ce.jpg

Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 8.0 ksi, S, = 10.5 ksi, and Sy = 8.0 ksi. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point.

Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 8.0 ksi, S, = 10.5 ksi, and Sy = 8.0 ksi. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 52 MPa, Sy = 63 MPa, and Sxy = 29 MPa.(a) Determine the principal stresses and the maximum in-plane shear stress acting at the point.(b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)(c) Compute the absolute shear stress at the point.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 28 MPa, Sy = 67 MPa, and Sxy = 23 MPa. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
SHow complete solution and include necessary figure. At a point, the normal and shear stresses acting on one plane are 8,000 psf compression and 2,000 psf, respectively. On a perpendicular plane, the normal and shear stresses are 2,000 psf compression and 2,000 psf, respectively. (a) Draw the Mohr’s circle. (b) Determine the value of the principal stresses. (c) Find the angle between the plane on which the 8,000 psi compressive stress acts and the major principal plane. (d) What is the maximum shear stress acting at the point?
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 700 psi in size.(a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element.(b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 30 MPa, Sy = 64 MPa, and Sxy = 23 MPa.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses and the maximum in-plane shear stress acting at the point.(c) Show these stresses on an appropriate sketch (e.g., see Fig. 12.15 or Fig. 12.16).(d) Determine the absolute maximum shear stress at the point.
Show complete solution, include necessary figures. The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension.A. Draw the Mohr's circle for this stress combination.B. What is the maximum shear stress acting at the point and what value of normal stress acts on the plane?C. Determine the value of the normal and shear stress acting on a plane that is 30 degrees from the minor principal plane.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 150 MPa, Sy = 21 MPa, and Sxy = 85 MPa. Assume β = 56°.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses and the maximum in-plane shear stress acting at the point. Show these stresses on an appropriate sketch (e.g., see Fig. 12.15 or Fig. 12.16).(c) Determine the normal stresses and the magnitude of the shear stress on the indicated plane and show these stresses on a sketch.(d) Determine the absolute maximum shear stress at the point. Answer:(a) Draw Mohr's Circle for this state of stress.(b) σp1 = MPa σp2 = MPa τmax in-plane = MPa(c) σn = MPa τnt = MPa(d) τabs max = MPa
The figure shows an element in bi-axial stress and the corresponding Mohr’s circle. Points A and B represents the stresses on the x face and on the y face of the element respectively. A. What is the value of the normal axial stress along x direction? B. What is the value of the normal axial stress along y direction? C. What is the value of the maximum shear stress?
Using the equations for determination of stress at a point, calculate the value for the maximum shear stress that develops at a point if the major principal stress is 343 kPa compression and the minor principal stress is 133 kPa tension.
The figure shows the stress condition of an I-section beam at point A. With the Mohr circle method; 1-)Calculate the principal stresses, location and angle. 2-)Calculate the stress components that will affect the plane obtained by rotating the figure counterclockwise 25.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 100 MPa, Sy = 15 MPa, and Sxy = 65 MPa. Assume β = 50°.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses and the maximum in-plane shear stress acting at the point. Show these stresses on an appropriate sketch (e.g., see Fig. 12.15 or Fig. 12.16).(c) Determine the normal stresses and the magnitude of the shear stress on the indicated plane and show these stresses on a sketch.(d) Determine the absolute maximum shear stress at the point. Part 1. Calculate the average normal stress and determine the radius of Mohr's Circle. Then draw Mohr's Circle for this state of stress.Answer: