Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If oy = 22 ksi, determine the angle 0, corresponding to the orientation of the maximum in-plane shear stress. 8 ksi 45 ksi O 30.1° or -56.6° O 20.2° or -79.2° O 22.6° or -53.0° O 27.6° or -62.4° O 16.7° or -85.4°

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If oy = 22 ksi, determine the angle 0, corresponding to the orientation of the maximum in-plane shear stress. 8 ksi 45 ksi O 30.1° or -56.6° O 20.2° or -79.2° O 22.6° or -53.0° O 27.6° or -62.4° O 16.7° or -85.4°

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
If M=50 kN-m, what is the bending stress at the center of the upper hollow circle about the z-axis? (in MPa).
The vertical bars AB and CD have a shear modulus G = 3.7 x 106 .Determine: the maximum shear stress in the bar CD and the rotation of point C. Consider fixed points B and D.
The normal and shear stresses on a plane are 120 psi (C) and 25 psi respectively. On an orthogonal plane, the respective stresses are 40 psi (C) and 25 psi. Draw Mohr's circle and determine the angle between minor principal plane makes with the 120 psi stresses.
The bar has a 140 mm by 20 mm rectangular cross section. If P = 190 kN, determine the force components perpendicular (N) and parallel (V) to a-a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a-a.
P = 49 kips Determine the normal and shearing stress at point a, b, and c
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
6. A simply supported beam carries a concentrated load of 24 kN at 6 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees. ROUND OFF TO FIVE DECIMAL PLACES.
What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object? The shearing stress value will be The angle of twist will be
Determine the vertical displacement at Joint A, B, C, D, E
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa