Consider a turbine that operates between two states (1, 2) and a compressor that operate between two states (3,4) if they are subjected to some heat loss with affecting the initial and final states then : Select one: A. Other parameters need to be known to determine the heat loss effects on W, and W c,in t,out В. W t,out increases and W. decreases due to c,in. heat loss. C. W. decreases and t,out W. heat loss. C.in increases due to c,in D. Both W, and W. t,out сin decrease due to heat loss. O E. Both W, and W t,out c,in increase due to heat loss.

Consider a turbine that operates between two states (1, 2) and a compressor that operate between two states (3,4) if they are subjected to some heat loss with affecting the initial and final states then : Select one: A. Other parameters need to be known to determine the heat loss effects on W, and W c,in t,out В. W t,out increases and W. decreases due to c,in. heat loss. C. W. decreases and t,out W. heat loss. C.in increases due to c,in D. Both W, and W. t,out сin decrease due to heat loss. O E. Both W, and W t,out c,in increase due to heat loss.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter46: Room Air Conditioners

Section: Chapter Questions

Problem 15RQ

See similar textbooks

Similar questions

A gas is compressed isentropically from 120 psia, 3.5 cubic feet per seconds and 40 deg F to 325 psia. For both non flow and steady-flow process, compute (a) T2 and V2, (b) PdV and – VdP, (c) ΔH, ΔU and ΔS, and (d) Wnf, Wsf and Q. Use Cp = 3.425 BTU/ lbm-R and k = 1.25
A steam turbine is operated under the following steam conditions:a. Steam in: P1 = 10 atm (abs) ; and T1 = 200oCb. Steam out: P2 = 0.8 atm (abs) ; and T2 = 105oCCalculate TSR, ASR and estimate this type of steam turbine!
Pls. answer thank you! A steam turbine of 6 MW capacity has a Willan's line equation of ms = 5.52 + 3.200 kg/hr. Determine the steam consumption at 63% load, kg/hr.
please written solution by hand and how can com h6 and s6 when T turbine inlet = 130 C , P heat exchanger = 20 bar , P condenser = 5 bar , Tw . cond out = 25 C Tw cond in = 17.5 C efficiencies compressor = 67.5 efficiencies turbine = 78 m. refrig =0.4 kg/s
SHOW COMPLETE SOLUTION THANK U 1. Steam expands steadily at a constant temperature. The flow rate is 13.6 kg/min with an inlet state of wet steam (water) at 80% quality to a final state of 700C and 2.5 MPa. The change of kinetic energy across the device is 3.5 kJ/kg, and the heat added is 21.81 kW. Determine (a) the enthalpy of conditions 1 &2, (b) the heat transfer in kJ/kg, (c) the work, and (d) the system power.
A steam power plant is located in the northern part of the country. Steam in the plant flows steadily through a 0.17-m diameter pipeline from the steam generating unit (SGU) to the steam turbine. At the SGU end, the steam conditions are determined to be P = 4 MPa, t = 400°C, h = 3,247 kJ/kg, and specific volume = 0.181 m³/kg. At the steam turbine end, the conditions are found to be P = 3.5 MPa, t = 392°C, h = 3,178.3 kJ kg, and specific volume = 0.248 m³/kg. Heat loss from the pipeline is 7.86 kJ/kg. Determine the steam mass flow rate in kg/s.
Air enters a blower at 20°C and exits at 28.38°C. The inlet velocities of air are 100 m/s and 150 m/s respectively. Find the mass flow rate if the blower consumes a power of 15 kW, assuming adiabaticconditions. Take cp of air is 1.005 kJ/kg-K. Need answers and solutions. ASAP...
.The refrigerant volume flow rate at the entrance of compressor wereobtained from a test on a twin cylinder single acting 15 cm x 20 cm, 320 rpmcompressor ammonia refrigerating plant 33 L/s. Determine the volumetricefficiency of the compressor.
Energy balance results (in kW) obtained for the same medium speed single cylinder diesel engine are reported in the following table. For case 1, if the coolant temperature is 105 °C at the outlet of the engine and the volumetric flow rate is 0.22*10-3 m3/s, the temperature of the coolant at the inlet is (in °C): (The coolant is considered water with a density 999 kg/m3 and a specific heat 4.2 k/kg.K). Case N (rpm) bmep (bar) W. O ambient Q ahast shaft 2.2 4.2 19.1 60.3 9.90 3.52 1 500 7.1 24.5 23.8 500 6.1 3.6 5.2 400 3.50 4.9 4.1 1.4 Select one: O a. 142.1 O b. 112.7 O c. 97.31 O d. 87.2 O e. 370.31
p88#5. while the pressure remains constant at 689.5 kPa the volume of a system of air changes from 0.567m^3. what are the (a)internal energy,(b) enthalphy ,(c) Q, (d) entropy, (e) if the process is nonflow and internally reversible,what is work?
In a three-stage compressor, the pressure ratio in each stage is equal and its value is 1.3, the first inlet temperature to stage 300K, outlet pressure from first stage 1000mmHg, , Polytropic yield 0.92. m C1 C2 = C2s C3 C3s = 500 "It s Isentropic exponent=1.4, coefficient of heating heat under constant pressure= 1005 kgK' your mercury density= 13550 and gravitational acceleration= 9.81 m3 m3 a) Find the actual and isentropic temperature of the exit from the 1st stage. b) Find the actual and isentropic temperatures of the exit temperatures from the 2nd stage. c) Find the real and isentropic work consumed in Stage 2. d) Put the available data and your calculations in the compressor (h-s) diagram.
Air flows steadily through an engine at a constant temperature, 400K. What is the work per kg if the exit pressure is one third and the inlet rpessure is 207 kPa? Assumr the kinetic and potential energy variation is negligible. R=287 kJ/kg K. A. 14.5 kJB. 210.7 kJC. 126.1 kJD. 126.3 kJ