Answered: Consider a two-port tank as shown in…

Name: 5Consider a two-port tank as shown in the figure given below with D₁
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 5Consider a two-port tank as shown in the figure given below with D₁ =4 cm, V₁ = 18 m/s, D2 = 7 cm, and V2 = 8 m/s as shown. If the tanksurface rises at 130 mm/s, determine the tank diameter.Tank area A₁----·Fixed CSmPaPw

Engineering

Mechanical Engineering

Consider a two-port tank as shown in the figure given below with D₁ = 4 cm, V₁ = 18 m/s, D2 = 7 cm, and V2 = 8 m/s as shown. If the tank surface rises at 130 mm/s, determine the tank diameter.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The second question: Answer the following briefly:۔ (1) What is the purpose and practical benefit of calculating the pressure center, and when is the amount of force calculated and its direction and center of influence calculated? (2) What does Bernoulli's theory state? (3) What is hydraulic ramp line (H.G.L).
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the lid (D = 4 m). If the weight of the lid is neglected, it is necessary to keep the lid in balance. Find the size of the force (Fa) required, as shown. Take the density of the water as 999 kg / m3.
Provide complete solution and diagram for this problem. What is the equivalent head of 15cm mercury in water ? A. 10m B. 1.36m C. 2.04m D. 16.34m
The flow of water from a reservoir is controlled by an L-shaped gate hinged at point A, as shown in the figure. The mass of the weight at B (a = 4 m to the right of A, b = 3 m above the base) is 5125 kg. If the gate opens when the water height is 1.75 m above the base, determine the width (in meters, not showing) of the gate.
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
The curved surface given in the figure is defined by y = 3 x−−√x . Determine the horizontal force and its line of action applied by water on the curved surface. The width of the gate is b = 2.3 m. Take the density of water to be 1000 kg/m3. Height of the water is 5 m
The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover is D = 4 m. Find the magnitude of the applied force (Fa) as shown. Take the density of water as 999kg / m3.
A closed cylindrical vessel of diameter 20 cm and height of 100 cm contains water up to height of 70 cm. The air above the water surface is at a pressure of 78.48 kPa. The vessel is rotated at speed of 300 rpm about its vertical axis. Find the pressure head in m at the bottom edge of the vessel. CHOICES: a.8.95 m b.8.06 m c.8.45 m d.7.86 m
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Figure. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B.Determine the force exerted on the plate by the ridge.
The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to adepth of 2 meters. It was subjected to an unknown rightward acceleration, ax, and a downward acceleration, ay, equal to 3 m/s2.a.) If after the acceleration, the oil depth is 1.5 m, determine the value of ax. Assume unit width.b.) Calculate the pressures at A and B during the acceleration.
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation for the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover (D = 4 m). Find the magnitude of the applied force (Fa) as shown.
The submerged sector gate AB shown in the figure is 1/9 of a circle of radius 4 m. The length of the gate is 10 m. Determine the horizontal component of water pressure acting on the gate.