Consider that you are in an area of Seattle where the wind is blowing at 40 km/h with a temperature of 0 ° C. If you can be mathematically modeled as a cylinder with diameter external of 0.3m and height of 1.70 m. Calculate the number of hot dogs that you need to eat to make up for the amount of energy you lose in heat form for an hour. Note 1: Consider that the external temperature of the clothes is kept constant at 25 ° C. Note 2: Consider a 150 kcal hot dog.

Consider that you are in an area of Seattle where the wind is blowing at 40 km/h with a temperature of 0 ° C. If you can be mathematically modeled as a cylinder with diameter external of 0.3m and height of 1.70 m. Calculate the number of hot dogs that you need to eat to make up for the amount of energy you lose in heat form for an hour. Note 1: Consider that the external temperature of the clothes is kept constant at 25 ° C. Note 2: Consider a 150 kcal hot dog.

Name: Consider that you are in an area of Seattle where the wind is blowing
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Consider that you are in an area of Seattle where the wind is blowing at 40 km/hwith a temperature of 0 ° C. If you can be mathematically modeled as a cylinderwith diameter external of 0.3m and height of 1.70 m. Calculate the number ofhot dogs that

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.52P

See similar textbooks

Similar questions

Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
5.6 A fluid flows at 5 over a wide, flat plate 15 cm long. For each from the following list, calculate the Reynolds number at the downstream end of the plate. Indicate whether the flow at that point is laminar, transition, or turbulent. Assume all fluids are at 40°C. (a) air, (b) , (c) water, (d) engine oil.
1-The wind blows with velocity 0.4 m/s parallel to the both sides of a flat plate with rectangular area 10m×10 m. The plate temperature is T0=60◦C, and the temperature of the air free stream is 20◦C. Assume laminar flow and calculate: (a) maximum boundary layer thickness, (b) the total force experienced by the plate, (c) estimate the total heat transfer rate by laminar forced convection (d) Make a qualitative sketch of how the local heat flux qx and τx varies along the length L.
A bicycle rider tries to coast for 300 m to complete one full circuit of a nominally flat oval shaped “track” in an elementary school parking lot on a non-windy day with the air temperature at 20oC. The mass of the rider is 85 kg and the mass of the bike is 12.5 kg. How fast does the initial speed need to be to coast the desired 300 m? Is attaining this speed feasible (i.e., can the rider generate this speed by pedaling on horizontal surface)? Assume: •The rider crouches down a bit to reduce drag (as compared to sitting upright) •The rider cannot maintain balance if the speed gets below 0.1 m/s. •All resistance is due to wind drag
Air is flowing at a speed of 30 m/sec over a flat plate. The air temperature is 20o C and its pressure is 1 atm. The plate is kept at a constant temperature of 65o C. What is the heat transfer rate per unit length between 7.5 cm to 30 cm, from the edge of the plate?
Subject : Thermofluid Question : A wind turbine four 10 cm diameter cups with a center-to-center distance of 40 cm, as shown in Figure 4. Due to a malfunction, the pivot is suddenly stuck, and the cups stop rotating. If the wind speed is 12 m/s moving at the described direction and air density is 1.25 kg/m3. Determine the maximum torque this turbine applies on the pivot.
A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to measure wind speed. Consider a wind turbine with four 1-cm-diameter cups with a center-to-center distance of 22 cm, as shown in Fig. 1. The pivot is stuck as a result of some malfunction, and the cups stop rotating. For a wind speed of 20 m/s and air density of 1.25kg/m3, determine the maximum torque this turbine applies on the pivot.