Suppose at certain speed, your car has the air drag force of 290 N and the rolling resistance of 370 N. What is the total amount of energy required to drive 10 km against these two forces? (Amusing the Energy efficiency of the car engine is 25%). (Report your result in MJ, i.e. 10^6 J). Your Answer: Answer

Suppose at certain speed, your car has the air drag force of 290 N and the rolling resistance of 370 N. What is the total amount of energy required to drive 10 km against these two forces? (Amusing the Energy efficiency of the car engine is 25%). (Report your result in MJ, i.e. 10^6 J). Your Answer: Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A beach ball 20 cm in diameter traveling at a speed of 50 m/s in still air at 30°C is found to have a drag of 8 N. (a) Find the velocity at which the drag of a 60 cm sphere immersed in water at 15°C can be found from the above data. (b) What is the drag of the larger sphere at this velocity?
A solid cone of angle 2Ɵ, base r 0 , and density ρ c is rotating with initialangular velocity ω 0 inside a conical seat,as shown below. The clearance h is filled with oilof viscosity μ. Neglecting air drag, derive an analytical expression for thecone’s angular velocity ω(t) if there is noapplied torque.
A 30 cm diameter cork ball (S=0.21) is tied to the bottom of a river as shown. (a) Draw the free body diagram of the ball. (b) Calculate the tension in the string and the drag force on the ball. (c) Estimate the speed, Uo of the river current Hint: Volume of a sphere = (1/6)πD³.
A road haulage truck has an approximate rectangular frontal area 2.5 m wide by 3.8 m high. To investigate the drag on the truck, a one – fifth scale model is to be tested in a wind tunnel. We can assume that the density and viscosity of the air are the same for the model as for the full size truck. If the truck travels at 120 km/h, what is the appropriate air speed for the model in the wind tunnel?
A student wants to estimate drag force on a golf ball of diameter D moving in air at a speed of U at atmospheric conditions. The student has access to a wind-tunnel and develops a replica of the ball that is 5 times smaller in diameter sets the wind speed 5 times larger than the actual golf ball. Compared to the force on the replica, the estimated drag force on the actual golf ball will be
a test tank will be used to measure the drag of a scale model ship 0.8 m long. This model bears full resemblance to a 40 m long prototype ship that was designed to sail at a speed of 10 m / s. Evaluate: a) the speed of the modelb) the ratio between the drag forces of the model and the prototypec) the relationship between the powers needed to overcome the drag of the model and the prototype take the number of froud into account in your analysis.
The drag equation for the Gofaster 172 is: D = 0.0003v2A. D is drag in pounds; v is airspeed in feet/second; and A is aircraft frontal area in square feet. At maximum airspeed, D = 140 lbs. How much does max airspeed INCREASE if the fuselage is narrowed such that frontal area A is reduced from 16 ft2 to 14 ft2? Give the answer in ft/sec AND mph. drag is 140 lbs. at maximum airspeed, regardless of frontal area. the question is: what is the INCREASE in max airspeed, not what is the max airspeed.
Suppose you are designing the propeller of a radio-controlled model airplane. The overall diameter of the propeller is 34.0 cm, and the hub assembly diameter is 5.5 cm. The propeller rotates at 1700 rpm, and the airfoil chosen for the propeller cross section achieves its maximum efficiency at an angle of attack of 14°. When the airplane flies at 30 mi/h (13.4 m/s), calculate the blade pitch angle from the root to the tip of the blade such that ? = 14° everywhere along the propeller blade.
Assume that the Flettner rotor ship of Fig. has a waterresistance coefficient of 0.005. How fast will the shipsail in seawater at 20°C in a 20-ft/s wind if the keel alignsitself with the resultant force on the rotors? [Hint: This is aproblem in relative velocities.]
Fluid Mechanics Problem: A ship is 150 m long and has a wetted area of 5000 m2.If it is encrusted with barnacles, the ship requires 7000 hp to overcome friction drag when moving in seawater at 15 kn and 20oC. What is the average roughness of the barnacles? How fast would the ship move with the same power if the surface were smooth? Neglect wave drag. Note: Treat the ship hull as a flat plate. Use eq. 7.48b to find effective barnacle roughness height.Use equation (7.45) White for the drag coefficient CD = D/.5pV2A , where A is the hull (plate) area, to find the ship velocity for smooth plate.
Icebergs can be driven at substantial speeds by the wind.Let the iceberg be idealized as a large, flat cylinder, D >> L,with one-eighth of its bulk exposed, as in Fig.. Letthe seawater be at rest. If the upper and lower drag forcesdepend on relative velocities between the iceberg and thefluid, derive an approximate expression for the steady icebergspeed V when driven by wind velocity U.
You are given a drone with an average chord length of 8 in., a wingspan of 2.5 ft, and a weight of 300 g. Based on figure 2, would it stay in the air at a speed of 5 m/s? (Assume ρ=1.225 kg/m3 and Nu=1.516*10-5 m^2/s)