please solve correctlt Consider the beam shown in (Figure 1). Suppose thatM=35k ft. EI is constant. Solve this problem usingthe moment-area theorems.Figure-15 ftB9 ft1 of 1MPart BDetermine the displacement at C measured upward.Express your answer using three significant figures.Ac =SubmitPart C0c =OFIVE ΑΣΦ |SubmitRequest Answervec 4Determine the slope at C measured counterclockwise from the positive x axis.Express your answer using three significant figures.IVE ΑΣΦ ↓↑ vec 4Request Answer?2?Reviewx 1 k-ft³EIX 1 k.ft²EI

Given data:- M=35 k EI is constant Below figure is given;

Consider the beam shown in (Figure 1). Suppose that M 35 k ft. EI is constant. Solve this problem using the moment-area theorems. Figure 15 ft B < 1 of 1 -9 ft M ▼ Part B Determine the displacement at C measured upward. Express your answer using three significant figures. ΠΙΑΣΦ | 11 vec ← Ac = Submit Part C 0c = Request Answer Submit Determine the slope at C measured counterclockwise from the positive axis. Express your answer using three significant figures. ΠΫΠΙ ΑΣΦ | Request Answer ? vec ? Review x 1 k-ft³ ΕΓ X 1kft2 EI

Consider the beam shown in (Figure 1). Suppose that M 35 k ft. EI is constant. Solve this problem using the moment-area theorems. Figure 15 ft B < 1 of 1 -9 ft M ▼ Part B Determine the displacement at C measured upward. Express your answer using three significant figures. ΠΙΑΣΦ | 11 vec ← Ac = Submit Part C 0c = Request Answer Submit Determine the slope at C measured counterclockwise from the positive axis. Express your answer using three significant figures. ΠΫΠΙ ΑΣΦ | Request Answer ? vec ? Review x 1 k-ft³ ΕΓ X 1kft2 EI

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the slope at A and displacementat C. EI is constant. answer should be θ = -5/EI kN/m2 counterclockwise;Δ = -2.8125/EI kN/m3 upward
Given a cantilever beam of length L=3.1meters. The left support “A” is fixed while the right end “B” is free. With constant EI=20000 KN-m2. A downward uniform load of 61KN/m is applied all throughout its span. Using Area Moment Method (AMM), calculate the deviation of A when a tangent line is drawn at B, i.e. tA/B? Express your answer in "millimeters" in 2 decimal places. Include negative (-) sign if tA/B is negative.
A 6m simply supported beam AB carries 2 concentrated downward loads of P=65KN each placed at third points of the beam span. With constant EI=21000 KN-m2. Using Double Integration Method (DIM) with origin taken at point A (left support) where 0 ≤ x ≤ 6m, calculate the slope at the left support A? Express your answer in "degrees" in 3 decimal places. Take note that 180 degrees = pi radians.
Q1/Find the horizontal displacement at C . and @y by using Virtual Work Method, i you know E - 200 GPa, I - 25°(10% mmé , (P KN)
(a) Compute the vertical deflection and slope of the cantilever beam at points B and C in Figure P8.20. Given: EI is constant throughout, L = 12 ft, and E = 4000 kips/in.2 . What is the minimum required value of I if the deflection of point C is not to exceed 0.4 in.?
(a) Draw qualitatively the deflection curve based on the bending moment diagram. (b) Determine the deflections at B and D, and the slope at C by the moment area method. (c) Locate the point of maximum deflection in AB and compute its magnitude. (E = 200GPa, I = 107mm4 )
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following using slope deflection method: 1. Slope at B, in radians
Given a cantilever beam of length L=4.5meters. The left support “A” is fixed while the right end “B” is free. With constant EI=20000 KN-m2. A downward uniform load of 56KN/m is applied all throughout its span. Using Area Moment Method (AMM), calculate the deviation of B when a tangent line is drawn at A, i.e. tB/A? Express your answer in "millimeters" in 2 decimal places. Hint: tB/A = deflection at free end. Include negative (-) sign if tB/A is negative.
Determine the slope and displacement at the end A of the beam. Take E=29(10^3) Ksi, I=170in^2. Use the method of virtual work
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
1. Determine the equations of slope and deflection. 2. Determine the slope and deflection at point 3m from point A. E =210 GPa. 100 | Cross section 6KN.m 2m B8KN 2 kN/m 2m T ) B8KN 2m
determine the slope at point B in radian. The equation of elastic curve are the following: E = 200 GPa, I = 1660 x 10^6 mm^4 Let w = 118kN/m, L = 13m