Consider the circuit in Fig. 16.12(a). Find the value of the voltage across the capacitor assuming that the value of v,(t) = 10u(t) V and assume that at t= 0, -1 A flows through the inductor and +5 V is across the capacitor.

Consider the circuit in Fig. 16.12(a). Find the value of the voltage across the capacitor assuming that the value of v,(t) = 10u(t) V and assume that at t= 0, -1 A flows through the inductor and +5 V is across the capacitor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.21MCQ

See similar textbooks

Related questions

Q: Two resistors connected in parallel The value of the first resistance is 6 ohms and the value of the…

A: We need to find out equivalent resistance

Q: on -10 -15 -20 20 15 10 5 1 2 3 I 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 t (ms)

A: The given waveform is shown below: The average value of the waveform is determined from the area…

Q: For the oscilloscope trace of a sine wave. Each horizontal division represents 200μs and each…

Q: Write down the different method of power transmission?

A: In the above given question we need to list different methods of power transmission.

Q: 6. a sinusoidal current is in phase with the voltage. It has an active power of 50VARS and reactive…

A: given here reactive and active power and asked to find the apparent power.given here series RLC…

Q: For the following circuit, the resistance of R2 is 20 mA SR2 R3 2ΚΩ 100 mA SR1 2ΚΩ 4Ω 8 ΚΩ 2 ΚΩ 8 Ω…

A: We need to find out the value of resistance for given circuit

Q: The average value for the following current waveform is i (A) ИМ 01 2 3 4 5 67 6 А 12 A 4А ЗА 2A…

Q: Use Thevenin's theorem to find 1, in the circuit in Fig.1. 2/0° A -j2 카 4/0° A 6/0° V In To Fig.1 10

Q: . Find the current density when the magnetic flux density is equal to 50 μ unit and the differential…

Q: 45. Equivalent electrical parameter of MMF in electric circuits. a. Voltage b. Resistance C. Current…

A: For the above given multiple choice questions we need to find the correct option with reference to…

Q: B-For the lossless transmission lines circuit shown below, design the value of Rx for proper series…

A: Given figure,

Q: A- Assume you have a Frequency Modulator where its instantaneous frequency varies with the message…

Q: Consider the circuit in Fig. 16.12(a). Find the value of the voltage across the capacitor assuming…

A: convert the circuit in s -domain 10 u(t)⇒10s5H⇒sL⇒5s0.1F⇒1sc⇒10s…

Q: The dc motor has maximum current at start because: O The back emf is maximum. OThe back emf is zero.

A: here we have to find why the dc motor has maximum current at the start.

Q: 2.41: For the current locus diagram shown beside: Draw the equivalent electric circuit diagram…

A: Solution- Given, Vs=220∠10° V We take Vs as a reference voltage then Vs = 220∠0° V I1 = 30∠30° AI2…

Q: The behavior of oscillator is described by Olong periods of dissipation followed by short impulses…

A: Oscillators are nothing but the device which works on the principle of oscillations.These are used…

Q: The voltage and current of a load are v(t)=5cos(5nt+15) and i(t)=0.5cos(5t+45), respectively.…

A: Given, The voltage and current of a load are, vt=5cos5πt+15°it=0.5cos5πt+45°

Q: The efficiency of a 1000kVA, 110/220V, 50Hz single phase transformer is 98.5% at a half load 0.8 p.f…

Q: A price change causes the quantity demanded of a good to decrease by 30%, while the total revenue of…

Q: Q1) A) What is bus? How many ways to construct bus system. (explain with example for one type)

Q: 4. The input-output relationship for a linear, time-invariant, and casual system is defined by the…

A: Fourier series: This is a mathematical tool for expanding the periodic signal in the term of their…

Q: If the baud rate for a 64-QAM signal is 1000 bauds/sec, what is the bit rate? Select one: O a. 4000…

A: Given: A 64-QAM signal with Baud rate=1000 bauds/sec

Q: 4. A disturbance is a desired input signal that affects the system output signal. 5. An advantage of…

A: We need to tell about whether the given statement are true or false

Q: A dc separate excited generator operate at speed = 1500 R.P.M at a certain excitation gives a…

A: Given data, A dc separate excited generator, Case1) Operated speed = 1500 R.P.M at a certain…

Q: The amount of charge represented by four million protons

A: Given:Number of protons=4×106To find:The amount of charge represented by 4 million protons

Q: For the following circuit, number nodes is R₂=402 E₂=6V- R3=302 E₁=2 V R₁ = 20

A: In this question we will write no of nodes...

Q: Q.2) Consider the fixed-gate bias circuit of JFET shown below with the following parameters obtained…

A: The dc circuit is given below Now we need to find dc parameter by dc analysis.

Q: والصورة المرتبطين بحسابك على Google عند تحميل الملفات وإرسال هذا يكون جزءا من رداد الإلكتروني الذي…

A: Note:- As relative permiability of core is not given. I solved this question by assuming…

Q: For the following circuit, number of nodes is R₂=402 www E₂=6V R₂=30 W R₁=102 E₁ = 2 V R₁ = 20 E3= 1…

Q: 7. A transmission line has the following per-unit-length parameters: L = 0.25 uH/m, C= 100 pF/m,…

Q: 32. The charge within a conductor will be: a. Greater than 1 b. Less than 1 C. Zero d. Infinite 33.…

A: Given, 32. The charge within a conductor will be a.Greaterthan 1 b.Less than 1 c. Zero d. Infinity…

Q: Compute the voltage (t) at the leady- 32 F 6(t) ни 201 472 E. UF for Eo 12v and e(t) 4 sin(32 +90%)…

A: Given data : Eo=12v e(t)=4sin(3t+90°)v

Q: For the 3 Circuit shown, -re the tatal power absorbed 208 10+140 sequence. [15 Calculate 6-18

Q: B) State the junction bias conditions for a bipolar junction transistor operating as an amplifier.…

A: The BJT can be used in three different types of configuration which are listed below :…

Q: 10- A unity feedback system has open-loop transfer function G(s)=2/ (S+4), the ratio of time…

Q: Using mesh analysis, determine the currents for the network of fig (5) www 652 A 8 A W 212 Fig-5 852

Q: 48. One weber is equal to: a. 1x 108 Maxwell b. 1x 106 Maxwell C. 1 x 10° Maxwell d. 1x 10¹0 Maxwell…

A: 48. One Weber is equals to 49. According to Biot-savart and Ampere's Law, the direction of magnetic…

Q: * Plot Root Locus for the system (5+2) (5+2) te G(s)H(s) = S(S+5)(S+10)

Q: Find u (1) in the circuit shown in Fig. 16.9. Note that, since the volt- age input is multiplied by…

Q: Biot-Savart law in magnetic field is analogous to which law in electric field? a. Gauss's Law b.…

A: Biot savart law say that the magnetic field in a current carrying conductor at distance point is the…

Q: Q1) A) What is bus? How many ways to construct bus system. (explain with example for one type)

Q: 28. Find the magnitude of a curl of the vector at point (1, 1, −0.2); F = 30 ax + 2xy ay + 5xz² az…

Q: 4. For the Wheatstone bridge network shown in Figure. a) Evaluate the Wheatstone Bridge network and…

Q: Q1) Choose the Correct answer: 1- For the circuit shown below, if Zo is equal to 750. The value of…

A: Note: Since the given questions are not interlinked to each other hence according to the guidelines…

Q: 47. Flux linkage is equal to: a. Product of number of turns and magnetic flux b. Number of…

Q: Shunt generator will build up its voltage when: Olts field resistance higher than critical value.…

Q: The magnetizing equivalent circuit of transformer can be found by open circuit test O True O False

A: Open circuit test is conducted in the presence of rated flux in the transformer core. In order to…

Q: - B- Use Thevenin's Theorem to find the current through (R) in the circuit shown below. 2 A (1+ R3…

Q: For the resistive inductive load and free welling diode single phase fully controlled half wave…

A: Half-wave rectifier: Half-wave rectifier allows one half cycle and blocks other half cycle of the…

Q: 8. Find the complement of a. F=A'B + B'C' + D'

A: Given Boolean function, F=A'B+B'C'+D'

Question

Example 3.8:
Consider the circuit in Fig. 16.12(a). Find the value of the voltage
across the capacitor assuming that the value of v,(t) = 10u(t) V and
assume that at t= 0, -1 A flows through the inductor and +5 V is
across the capacitor.
it in ELECTRICA
fa
ww
REPARTM
%, (1)
ESH
(a)
0.1 F
INEERING

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Signal and system The mathematical model of a system is y" (t) + ay'(t) + by(t) = a (t) + ca (t) where a=1, b=2 and c=1. 1) Find zeros and poles of the system. 2) Show them onto the S-Plane (the complex plane) 3) Discuss the BIBO stability of the system.
A system is described by the differential equation (see attached). a)What is the order of the system. How many poles does the system's transfer function have. How many states are needed to describe the system completely.b) Determine the system's transfer function, Y(s)/U(s) (the poles of the system are at ―1, ― 2, and ―4);c) Determine matrices A, B, C, and D to describe the system in state-space form x' = Ax + Bu, y = Cx + Du.
: If F(s) = s 4+ 5s3+20s 2 + 40s + 50 , Investigate the stability of this system
Make the equation s(s+1)(s+2)+K=0 in the form of 1+KF(s) and explain the drawing of root-locus curves. (Note: Indicate the splitting points, centers and angles of the asymptotes)
identify the following 1. If the pole’s real value is positive and is located on the right side of the S-plane. The system exponentially ____________.2. Is a continuous connection of branches from one node to another with all arrowheads in the same direction.3. Knowing the location of the pole in the S-plane determines the ______________ of the system.
3. Consider the following second-order differential causal system: y ̈(t)+6y ̇(t)+8y(t) = 2x(t), x(t) = e−3t u(t), y(0) = 2, y ̇(0) = −6, (here, u(t) = step function) where x(t) and y(t) are the input and output of the system, respectively. Find the natural response yn(t), forced response yf (t), and total solution y(t) of the system.
s ( s+1 ) ( s+2) (s+3)+k =0 Draw the root-locus curves of the characteristic equation . (Note: Find the equation that gives the separation points of the root locus curves, but without solving the equation, give roughly the location of these points on the axis)
If ? = 50Ω, L = 1.5H, what value of C will cause a sourceless series RLC circuit to be a) overdamped ?, b) critically damped ?, c) underdamped?
Convolve the x(n) with h(n) * x(n) * and h(n) are given by, x(n) = (1, 2, 3) h(n) = (1, 2, 1)
Find and graph the current i(t) in the RLC-circuit in Fig. 149, where R = 1 Ω, L = 0.25 H, C = 0.2 F, v(t) = 377 sin 20t V, and current and charge at t = 0 are 0.
Using the DIFFERENTIAL EQUATION METHODS, Solve for the particular solution of the differential equation as follows:y"'+ 33y"+ 30y'− 64y= 0With the initial conditions as follows: y(0) = 0, y’(0) = -1, y’’’(0) = 33.
I need help with the question below Consider a causal LTI continuous system described by the differential equation y′′(t) + 3y′(t) + 2y(t) = x(t) where y(t) is the system output and x(t) is the input.1. Find the transfer function H(s) of the system.2. Find its poles and zeros. From its poles and zeros, determine if the system is BIBO stable or not.3. If x(t) = u(t) and initial conditions are zero, determine the steady-state response yss(t)4. If the initial conditions were not zero, would you get the same steady state?. Explain