Consider the data generated from a constant pressure filtration conducted at 200 kPa. Suppose the filtrate has a viscosity of 0.02 Pa-s and the slurry has a specific cake resistance of 3.61 x 108 m/kg and a concentration of 10 kg/m³, find the total filter area in m². Round off your answer to two decimal places. Show the graph as well Time Elapsed (min) 0 0.67 1.21 2.76 5.1 8.51 11.62 Cumulative volume collected, m³ 0 1.82 3.01 5.72 8.51 12.05 14.92

Consider the data generated from a constant pressure filtration conducted at 200 kPa. Suppose the filtrate has a viscosity of 0.02 Pa-s and the slurry has a specific cake resistance of 3.61 x 108 m/kg and a concentration of 10 kg/m³, find the total filter area in m². Round off your answer to two decimal places. Show the graph as well Time Elapsed (min) 0 0.67 1.21 2.76 5.1 8.51 11.62 Cumulative volume collected, m³ 0 1.82 3.01 5.72 8.51 12.05 14.92

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.18P: The drag on an airplane wing in flight is known to be a function of the density of air (), the...

See similar textbooks

Similar questions

Hydrostatic pressure at any given depth of a liquid depends on the_____ of the container.a)Volumeb)ShapeC)Depthd)All of the above .As the temperature of oil increases, the viscosity of oil willa) increaseb) decreaseC)not change Which of the following units would NOT be used for volume flow rate?a) gal/minb) Ib/sc)m⅗d)ft^3/s 2.Dynamic viscosity is defined as,a) weight per unit volume of a fluidb) volume per unit weight of a fluidc) the velocity gradient divided by the shearing stress of a fluidd)the shearing stress divided by the velocity gradient of a fluid
Kinematic viscosity /4 of water varies with temperature T as shown in the table. Determine the cubic that best fits the data, and use it to compute peg at T= 10°,30°,60°, and 90°C. by interpolation.) Solve by matlab
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.
A tape 30m long of standard length a 29Celcius was used to measure a line the mean temperature during measurement was 15Celcius, the measured distance was 221.65 m, the following being the slopes:1 degree 10’ for 60 m2 degree 20’ for 30 m5 degree 18’ for 30 m4 degree 40’ for 12 m1 degree 30’ for 30 m3 degree 48’ for 30 m7 degree 20’ for 18 m1 degree 20’ for 11.65 mFind the true length of the line if the coefficient of expansion is 116x10^-7 per 1Celcius
Use dimentional analysis to evaluate that in a problem involving shallow water waves (figure 6), both the Froude number and the Reynold's number are relevant dimensionless parameters. The wave speed, c of waves on the surface of a liquid is a function of depth h, gravitational acceleration g, fluid density, p and fluid viscosity μ. Manipulate your II's to get the parameters into the following form: Fr = c/(gh)1/2= f(Re) , where Re = pch/μ
The following table lists molecular weight data for a polypropylene material. Compute the number-average molecular weight, Molecular Weight Range (g/mol)//// xi////// wi 8,000–16,000//// 0.05/// 0.02 16,000–24,000 ///0.16// 0.10 24,000–32,000 ///0.24// 0.20 32,000–40,000 ///0.28// 0.30 40,000–48,000 ///0.20// 0.27 48,000–56,000 ///0.07// 0.11 Round your answer to 0 decimal places.
Please show all steps, not Ai generated A flow rate is a particular experiment is normally distributed with μ = 15 cfm and σ =1.25 cfm. What is the probability that the flow rate a) is at most 17 cfm, b) is between10 and 14 cfm, c) differs from 15 cfm by at most 1.25 standard deviations?
The following data are given for a biogas digester suitable for the output of six cows. The volume of digester is 8.3 m3 , the volume of gas holder is 2.2 m3 and the retention time is 22 days. Find the height of gas holder in centimeter.
An airplane builder wants to build a scaled-down model of a real airplane in a 12:1 ratio in order to be able to perform tests in a wind tunnel. The real plane flies at 126 km/h, while the air speed in the tunnel where the model is located is given by V. The performances of the two will be equivalent for a value of V, in m/s, equal to Data: air viscosity η = 1.8 × 10-5 kg/(m.s) air density ρ = 1.3 kg/m3
The drag on an airplane wing in flight is known to be a function of the density of air (), the viscosity of air(), the free-stream velocity (U), a characteristic dimension of the wing (s), and the shear stress on the surface of the wing (s). Show that the dimensionless drag, sU2, can be expressed as a function of the Reynolds number, Us.
Topic : Mixture Flow Problem A tank initially holds 100 gal of salt solution in which 50 Ib of salt has been dissolved. A pipe fills the tank with brine at the rate of 3 gpm, containing 2 lb of dissolved salt per gallon. Assuming that the mixture is kept uniform by stirring, a drain pipe draws out of the tank at 2pm. Find the amount of salt at the end of 30 minutes. Ans. 171.24 Ib
As an instrumentation engineer you are asked to measure pressure with accuracy rate of±0.1%, what does it imply?If the pressure actual readings are 2, 4, 5 kg/m2in the full scale division of 10 kg/m2then whatare the possible measured values of pressure if accuracy rate of instrument is ±0.1% FSD ?State your answer with justification for the following whether it is accurate and precise,accurate not precise, precise but not accurate and not accurate and not precise.