Consider the following figure. C2 (a) Find the equivalent capacitance between points a and b for the group of capacitors connected as shown in the figure above. Take C, = 3.00 pF, C2 = 14.0 LF, and C3 = 1.00 pF. (b) What charge is stored on C, if the potential difference between points a and bis 60.0 V?

Consider the following figure. C2 (a) Find the equivalent capacitance between points a and b for the group of capacitors connected as shown in the figure above. Take C, = 3.00 pF, C2 = 14.0 LF, and C3 = 1.00 pF. (b) What charge is stored on C, if the potential difference between points a and bis 60.0 V?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
4. In what form is the energy of a capacitor stored?
The charges of the 2C, C, 2C capacitance capacitors in the figure are qk, qi and qm, respectively. Accordingly, what kind of relationship is there between qk, qi and qm?
A charge Q is placed on a capacitor of capacitance C. The capacitor is connected into the circuit shown, with an open switch, a resistor, and an initially uncharged capacitor of capacitance 3C. The switch is then closed, and the circuit comes to equilibrium. In terms of Q and C, find (a) the final potential difference between the plates of each capacitor, (b) the charge on each capacitor, and (c) the final energy stored in each capacitor. (d) Find the internal energy appearing in the resistor.
Question2: Four capacitors are connected as shown in figure Q) find the equivalent capacitance between points a and b? b) calculate the charge on each capacitor taking AV, = 15V?
Determine the total capacitance, total charge, individual voltage drop and charges across across each capacitor. Use two decimal places for your answer. Please put your answer for the individual voltage and charge for each capacitor in a table for faster checking. Thank you! C1= 27 F C2= 53 F C3= 21 F C4= 50 F C5= 17 F C6= 22 F C7= 45 F C8= 16 F C9= 25 F C10= 16 F V= 110 V Note: This topic is under capacitors.
Capacitance= 4uF2) Determine the time constant of the circuit for the capacities 3) For the capacity value, calculate the estimated time to come to the final state.4) Plot capacitor current and voltage graphs and show if it works in harmony with the time constant you calculated. NOTE: if you want you can use falstad online circuit simulator.
Suppose we have a very large capacitance (ideally, infinite) charged to 10 V. What othercircuit element has the same current-voltage relationship? Explain your answer.
Having stabilized the fuel, you look to your computer for next steps. You are told that the spacecraft uses a "start capacitor" that must reach a required voltage in order to start its engine. This voltage is determined by the fixed capacitance and charge as a function of time, q(t) . These capacitors are charged and stored in your current location and must be brought to the spacecraft. Your computer provides you with the following definitions: Charge: The charge as a function of time is q(t)=∫i(t)dt , where i(t)=36t^5+15t^2−6 is the current as a function of time. You need to provide the computer with the function q(t) in order for it to appropriately charge the start capacitor. If an unknown constant is needed, it can be included using "+ C", being sure to use a capital letter as the lowercase is used for capacitance. q(t)=
2. A parallel plate capacitor with a plate area of 0.13 square meters separated by 1 mm is charged to 9 Volts by a battery, which is then disconnected. The plate separation is then increased to 40 mm.A. Using the expression for the capacitance of a parallel plate capacitor, what do you expect the new potential difference across the plates to be after the increase?B. Suppose you measure the potential difference across the plates after the separation and find it to be 30 V (this should be very different from what you found in part A). This unexpected result can be explained by the effects of “stray capacitance” with nearby objects. Assuming that the stray capacitance can be modeled as a capacitor connected in parallel with the parallel plate capacitor, find the value of this stray capacitance.
A 220 microfarad capacitor has an initial charged of 800 microcoulomb. It is discharged through a 100-Ω resistor. How long will it take in order for a capacitor to discharge to 100 microcoulomb? 150 microcoulomb? 200 microcoulomb? Make a graphical representation of equivalent charge vs time t, then interpret the graph
It is required to grade a string having seven suspension insulators. If the pin to earth capacitance are all equal to C, determine the line to pin capacitance that would give the same voltage across each insulator (C1, C2, …….C6) of the string.