Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with velocity of 1 m/s: atmospheric air, water, engine oil, and mercury. For each fluid, determine the velocity and thermal boundary layer thicknesses, in mm, at a distance of 40 mm from the leading edge. Fluid 8 (mm) d, (mm) Air i Water Engine Oil Mercury

Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with velocity of 1 m/s: atmospheric air, water, engine oil, and mercury. For each fluid, determine the velocity and thermal boundary layer thicknesses, in mm, at a distance of 40 mm from the leading edge. Fluid 8 (mm) d, (mm) Air i Water Engine Oil Mercury

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.25P

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
1.0 Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with velocity of 1 m/s: atmospheric air, water, engine oil, and mercury. For each fluid, determine the velocity and thermal boundary layer thicknesses, in mm, at a distance of 20 mm from the leading edge.
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C . The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 °C , what is the overall heat transfer at the laminar section?
Water at 45.0oC flows over a large plate at a velocity of 30.0 cm/s. The plate is 1.0 m long (in the flow direction), and its surface is maintained at a uniform temperature of 5.0oC. Calculate the steady rate of heat transfer per unit width of the plate. Properties The properties of air at 1 atm and the film temperature of (Ts+T∞)/2 = (5+45)/2 = 25°C are: ρ = 996.6 kg/m3, k = 0.610 W/m.oC, μ = 0.854x10-3 kg/m.s, Pr = 5.85
A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is flowing over a flat plate at a stream free velocity of 0.87 m/s. If the plate has a length of 2 m, answer the following: 1.What is Reynolds number at a point that is (1/4)L down the entrance? 2.Is the flow laminar or turbulent? 3.Calculate the thickness of the boundary layer in mm at (1/4)L down the entrance 4.Calculate the drag coefficient at (1/4)L down the entrance
Consider a bullet piercing through calm air during a short time interval in which the bullet’s speed is nearly constant. Determine if the time-averaged airflow over the bullet during its flight is one-, two-, or three-dimensional
Air at atmospheric pressure and a temperature of 25 degrees C is in parallel flow at a velocity of 5 m/s over a 1-m-long flat plate that is heated from below with a uniform heat flux of 1250 W/m2 . Assume the flow is fully turbulent over the length of the plate. Take ν = 18.76 × 10−6 m2/s, k = 0.0284 W/m·K and Pr =0.703. (a) Calculate the plate surface temperature, Ts(L), and the local convection coefficient, hx(L), at the trailing edge, x = L. (b) Calculate the average temperature of the plate surface.
A thin, flat plate that is 0.2 m × 0.2 m on a side is oriented parallel to anatmospheric airstream having a velocity of 40 m/s. The air is at a temperatureof T∞ = 20°C, while the plate is maintained at Ts = 120°C. The air flows overthe top and bottom surfaces of the plate, and measurement of the drag forcereveals a value of 0.075 N. What is the rate of heat transfer from both sides ofthe plate to the air?
Air at 20oC and 1 atm flows over a flat plate at 35 m/s. The plate is 75 cm long and 100 cm depth and is maintained at 60oC. Calculate (a) velocity boundary layer thickness at the leading edge, (b) thermal boundary layer thickness at the distance of 10 cm from the leading edge, and (c) thermal boundary layer thickness at the trailing edge.
Oilflow in a journal bearing can be treated as parallel flow betweentwo large isothermal plates with one plate moving at a constant velocityof 12 m/s and the other stationary. Consider such a flow with a uniformspacing of 0.7 mm between the plates. The temperature of the upperand lower plates are 47°C and 17°C, respectively. By simplifying andsolving the continuity, momentum, and energy equations, determine:(a) thevelocity andtemperature distributionsin the oil.(b ) the maximum temperature and where itoccurs.(The location ofmaximum temperature is determined bysetting dT/dy=0).(c) the heat flux from the oil to each plate
Air at 20 ◦ C flows inside a pipe 18-mm-ID having a uniform heat flux of 150 W/m 2 on the surface, the average flow velocity at entry being 1.0 m/s. The air pressure is 2 bar. Determine the value of convection coefficient. If the pipe is 2.5 m long, determine the air exit temperature and the wall temperature at the exit. Assume fully developed hydrodynamic boundary layer.