Consider the following mathematical model of a single-link flexible joint robotic manipulator (shown in the following figure) where the output of the system is y(t) = q₁(t), and I,m, g.l, k and are constants. lä(t) + MgLsin(q1(t)) + k(q1(t)-92(t)) = 0 Jäz(t)-k(q1(t)-92(t)) = u(t) a) Linearize the nonlinear dynamics at the working point q₁ =1=92=42=0. b) For parameters I = 2,J = 1, k = 1, g = 10, M = 0.1, L = 1, find the transfer function from input u to the output y.

Consider the following mathematical model of a single-link flexible joint robotic manipulator (shown in the following figure) where the output of the system is y(t) = q₁(t), and I,m, g.l, k and are constants. lä(t) + MgLsin(q1(t)) + k(q1(t)-92(t)) = 0 Jäz(t)-k(q1(t)-92(t)) = u(t) a) Linearize the nonlinear dynamics at the working point q₁ =1=92=42=0. b) For parameters I = 2,J = 1, k = 1, g = 10, M = 0.1, L = 1, find the transfer function from input u to the output y.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider two robot-manipulators:• A SCARA robot with joints displacement range q1,2 = −90◦...90◦ and q3 = 0..10cm and links lengths L1,2=10 cm.• A Cartesian robot with joint displacements’ range q1,2,3 = 0..10 cm.Which statement is correct?1) The Cartesian robot has a larger workspace.2) It is not possible to judge the workspace based on the information provided.3) Both robots have revolute joints.4) The SCARA robot has a larger workspace.
A manipulator’s end-effector position is calculated as follows:x = q0 cos q1 + l2 cos(q1 + q2),y = q0 sin q1 + l2 sin(q1 + q2),where q0,1,2 represent joint displacements and l2 is a constant positive parameter.Which of the following describes this manipulator:1) This is a robot-manipulator with 3 revolute joints.2) This is a robot-manipulator with 2 revolute and 1 prismatic joints.3) This is a robot-manipulator with 1 prismatic and 3 revolute joints.4) This is a robot-manipulator with 2 revolute joints. A robot’s end-effector’s tool position is defined asx = L1 cos(q1) + q3 sin(q1 + q2)where L1 = const, q1 = q1(t), q2 = q2(t) and q3 = q3(t) with t defining time. Calculate ∂x / ∂q3 1) it is impossible to calculate as the equation for the y and z positions are missing.2) cos(q1 + q2).3) it is impossible to calculate as time is not given.4) sin(q1 + q2).
I can't find support responses and section diagrams B is equal to one B=1
A planar mechanism has 8 links and 10 rotary joints. The number of degrees of freedom of the mechanism, using Grubler's criterion, is (a) 0 (c) 2 (b) 1 (d) 3
Find the transfer function T(s)=C(s)/R(s) for the block diagrams given in Fig.2 and Fig.3.
Derive the response relation for each of the models shown in Figure P1.25 assuming that the force F is constant and instantaneously applied.
I2 Q13_ Answer the following: (Answer with formula if needed with handwriting) - Structural Dynamic a) Determine the steady state response of the undamped SDOF system when it is excited by the force p(t) = sinwt (o = 0,). Assume zero initial condition. b) Discuss the modal analysis method.(short Answer) c) What is meant by sweeping matrix? d) Derive the Lagranges equation of motion for MDOF. e) what is Hamilton’s principle
A Block diagram of a feedback control system is shown in Figure Q3. Using the Block Diagram Reduction Method, solve for the output Y(s) when:(i) Input D(s) = 0,(ii) Input R(s) = 0,(iii) Input R(s) and D(s) are both applied (i.e., R(s) ≠ 0 , D(s) ≠ 0).
Determine the controllability and observability for this system
Topic: Time Response Please Make it digital instead of handwritten if applicable but it can't please make your handwritten readable. Thank you very much Please Answer No.1 Consider the translational mechanical network system shown on the figure. A 1-lb force, f(t), si applied at t=0. If fv=1, find K and M such that the response is characterized by a 4-sec settling time and a 1-sec peak time. Also, what is the resulting %OS?
a)If the system has a transfer function of the form G_P (s)=H(s)/(V_m (s) )=μ/(1+Ts) where µ is the gain and T is the time constant, calculate values for µ and T for the case where the valve is at position 3. Hints: Use the constants and information in table 1. The dynamics of the water tank can be found by applying the continuity equation: qin - qout = rate of change in water tank
A vibrating spring-mass system has the feedback control system shown in Fig Q3 below. (figure attached as image ACT)If K = 12.25 determine:6.1 the transfer function ; (3)6.2 the characteristic equation with a impulse input; (1)6.3 the un-damped natural frequency of the system; (2)6.4 the damping ratio; (2)6.5 the damped natural frequency; (2)6.6 the maximum percentage overshoot; (2)6.7 the peak time; (1)6.8 the settling time for the response within 2%. (2)