Consider the four bar suspension linkage shown in the figure.Use the given dimensions from the table below to write the→position vector rße describing the lowest link and the position→>>vector TGH describing the shock. Express each vector inCartesian components and also as a magnitude and an angle(measured counterclockwise from an x-axis defined parallel tothe ground and pointing right).h₂Variable Valueh₁10.3 inh₂17 inh318 inh412.6 inh5 5.7 in←"BE =W₂→rGH =Values for dimensions on the figure are given in the followingtable. Note the figure may not be to scale.→rGHat an angle ofWANAN→IBE has magnitude BE=at an angle ofVariable Value8.5 in5.1 in9.1 in6.8 in12 inW1W2W3W4W5îhas magnitude TGH =W4î+h₂h₂cc 30BY NC SA2013Michael Swanbom3) inchesinches and pointsdegrees CCW from horizontal.3) inchesinches and pointsdegrees CCW from horizontal.

Draw the given diagram for four bar suspension linkage with x-y coordinates. Write the given data.…

Consider the four bar suspension linkage shown in the figure. Use the given dimensions from the table below to write the → position vector TBE describing the lowest link and the position vector TGH describing the shock. Express each vector in Cartesian components and also as a magnitude and an angle (measured counterclockwise from an x-axis defined parallel to the ground and pointing right). h₂ h4 Variable Value h₁ h₂ h3 h5 kW,. "BE = W₂ → rGH = Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable W1 W2 W3 W4 W5 10.3 in 17 in 18 in 12.6 in 5.7 in IBE has magnitude BE = at an angle of TGH has magnitude TGH at an angle of = + W4 î+ W₁ hs Value 8.5 in 5.1 in 9.1 in 6.8 in 12 in h4 h₂ BY NC SA 2013 Michael Swanbom 3) inches inches and points degrees CCW from horizontal. 3) inches inches and points degrees CCW from horizontal.

Consider the four bar suspension linkage shown in the figure. Use the given dimensions from the table below to write the → position vector TBE describing the lowest link and the position vector TGH describing the shock. Express each vector in Cartesian components and also as a magnitude and an angle (measured counterclockwise from an x-axis defined parallel to the ground and pointing right). h₂ h4 Variable Value h₁ h₂ h3 h5 kW,. "BE = W₂ → rGH = Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable W1 W2 W3 W4 W5 10.3 in 17 in 18 in 12.6 in 5.7 in IBE has magnitude BE = at an angle of TGH has magnitude TGH at an angle of = + W4 î+ W₁ hs Value 8.5 in 5.1 in 9.1 in 6.8 in 12 in h4 h₂ BY NC SA 2013 Michael Swanbom 3) inches inches and points degrees CCW from horizontal. 3) inches inches and points degrees CCW from horizontal.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

projectile fired from A with v0 = 50m/s at angle of theta = 40 degree. neglecting air resistance, find radius of curvature p of path two seconds after firing, please show FBD and clear work.
A vehicle accelerates from a standing start up a 6 percent grade at an acceleration of 2 m/s2.Find the load distribution on the axles at this condition.The curb weights are 890 kg on the front axle and 500 kg on the rear. The wheelbase is 2,7m.Driver’s weight is distributed 49 percent on the front axle. Assume the driver weighs 90 kg.The height of CG is 50 cm.
A wagon weighing 5100 Kg moving at a speed of 8 km/h has to be brought to rest. Springs made of wire diameter 25mm with a Dm of 250mm and with 24 turns are available. Find the number of springs required in buffer to stop the wagon at a compression of 180mm. b)A close coiled helical spring is made of diameter wire 25mm. The spring index is 8. Findthe number of turns required and maximum allowable load if the allowable shear stress is100 MPa and elongation is limited to 40mm. [G=80 GPa
(13) A spring has an overall length of 44.0in & sustains a load of 15,000lb @ its center. The spring has three full-length leaves & 15 graduated leaves with a central band 4.0in wide. All leaves are to be stressed to 60,000psi when fully loaded. The ratio of total spring depth to width is to be approximately 2.0. Determine: (a) the width & thick ness of the leaves; (b) the initial space that must be provided between the full length & the graduated leaves before the band is applied; (c) What load is exerted on the band after the spring is assembled?
Complete the derivation of Eq. (8.15), which relates the tension in both parts of a V belt.(Reference to Equation 8.15):
A load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and tire is µT = 0.8. Wheel radius is twice the disc friction radius (Rt = 2 Rs), µ = 0.35 between pad and disc and allowable pressure p = 0.5 N/mm2 Determine the pad sizes and the hydraulic pressure that should be sent to the piston. Piston's diameter is d = 30 mm.
A semi-elliptic spring used for automobile suspension, consists of twoextra full-length leaves and eight graduated-length leaves, including themaster leaf. The centre-to-centre distance between the two eyes is 1 m.The leaves are made of steel 55Si2Mo90 (S = 1500 N/mm yt2 andE = 207 000 N/mm2) and the factor of safety is 2. The maximum springload is 30 kN. The leaves are pre-stressed so as to equalize stresses in allleaves under maximum load. Determine the dimensions of thecross-section of the leaves and the deflection at the end of the spring.
The spring in the figure extends 110 mm when loaded with a load of 18 kg. The weight is subjected to the periodic force F=12sin3t. The weight is pulled down 150 mm from the balance position and a downward velocity of 1.5 m/s is given. Subtract the differential equation describing the motion and determine the position equation. Assume positive displacement is measured upwards. (g=9.81m/s )
The figure shows an internal rim-type brake having an inside rim diameter of 11in and a dimension R of 3.5 in. The shoes have a face width of 1.25 in. Find the braking torque and the maximum pressure for each shoe if the actuating force is 205 Ibf, the drum rotation is counterclockwise, and f=0.32. The maximum pressure on the right-hand shoe parp is [ 16.99] @ psi. The maximum pressure on the left-hand shoe pa| H is [100.813 | @ psi. The torque on the right-hand shoe Tgis [ .056 | @ kipin. The torque on the left-hand shoe T is [ .332| @ kipin. Total braking torque Tiotal s [-3887] @ Kip-in.
A 6-in-wide polyamide F-1 flat belt is used to connect a 4-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 3. The center-to-center distance is 8 ft. The angular speed of the small pulley is 1850 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, F1a, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.
A hydraulic brake system is shown in the figure below. The radius of the input piston is 1.20cm and the radius of the output plungers is 3.40cm. The lengths associated with the lever arms of the brake pedal are L1 = 4.70cm and L2 = 13.0cm. Assume that the force delivered by each output plunger in the given situation is 273 N with the force applied by the foot being Fa. What is the gauge pressure inside the brake fluid?(A) 69.2 kPa; (B) 72.2 kPa; (C) 75.2 kPa; (D) 78.2 kPa; (E) 81.2 kPa. What is the torque (magnitude) produced by Fa?(A) 1.60mN; (B) 1.80mN; (C) 2.00mN; (D) 2.20mN; (E) 2.40mN. What is the value of Fa?(A) 7.53 N; (B) 8.03 N; (C) 8.53 N; (D) 9.03 N; (E) 9.53 N.
Calculate the amount of mass to be placed on the LCP and RCP with a radial radius of 0.2m in order to dynamically balance the shaft given on the right.m 1=3 kgm 2= 4 kgR 1=0.1mR 2=0.2m