help Determine the x and y components of F3 using scalar notation.Express your answers using three significant figures separated by a comma. Consider the gusset plate of a bridge truss shown in(Figure 1). Suppose that F1 = 8 kN, F2 = 6 kN,F3 = 4 kN , and F4 = 6 kN.Figure1 of 1F2F,88888

Given:- F1 = 8 kNF2 = 6 kNF3 = 4 kNF4 = 6 kN

Answered: Consider the gusset plate of a bridge…

Consider the gusset plate of a bridge truss shown in (Figure 1). Suppose that F1 = 8 kN , F2 = 6 kN, F3 = 4 kN , and F4 = 6 kN.

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 4STP

See similar textbooks

Related questions

Q: Calculate the forces in members CG and CF for the truss shown. 2 kN 2 m B 2 m C 2 m 4 kN 3 m F

A: SOlution: to find the force in CG and CF

Q: Q3. Use the method of joints to determine the magnitude and type of the internal axial forces for…

Q: In the figure, one end of a uniform beam of weight 150 N is hinged to a wall; the other end is…

A: Free body diagram:

Q: Why are the cross sections of metal beams in the shape of the letter I instead of solid rectangles?

A: I-shaped beam has higher bending strength and lower weight compared to the rectangular beam. In the…

Q: The forces on the gusset plate of a joint in a bridge truss act as shown. Determine the value of F…

Q: In the figure, one end of a uniform beam of weight 130 N is hinged to a wall; the other end is…

Q: For the three parts of this Quick Quiz, choose from the following choices the correct answer for the…

A: Introduction: There are three types of elastic modulus: 1) Young's modulus: It is the ratio of…

Q: A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal…

Q: The figure shows a 100.kg box suspended from the extreme side of the horizontal truss.…

A: In this problem we will use condition of static equilibrium.

Q: The horizontal boom supporting a lamp is of uniform construction and weighs 50 N. If the lamp…

Q: The two forces shown act on the structural member AB. Determine the magnitude of P (N) if Q=3885N…

Q: When the structure shown below is supported at the point P, it is in equilibrium. Find the magnitude…

A: For equilibrium condition, the force F2 m-2000 N2 m+1000 N2 m=0F2 m=4000 N.m-2000 N.mF=2000 N.m2…

Q: In the figure, one end of a uniform beam of weight 460 N is hinged to a wall; the other end is…

A: a)The expression for the tension in the wire,

Q: The diagrams below show forces of magnitude Fapplied to an equilateral triangular block of uniform…

Q: each pulley has a mass of 5 kg, what is the mass “M” that will hold the system in equilibrium?…

A: For equilibrium of object net force acting on it must be zero. So force in vertical and horizontal…

Q: The horizontal beam in the figure below (Figure 1) weighs 190 NN and its center of gravity is at its…

A: weight of beam = Wb = 190 N weight of load = WL= 300N Length of beam = L = 4m

Q: Three members of a truss frame into a steel gusset plate as shown. All forces are concurrent at…

Q: The forces on the gusset plate of a joint in a bridge truss act as shown. Determine the value of F…

Q: Q.3) Trusses are designed to carry: (a) axial load (c) torque (E) No one of above write your answer…

A: Answer A) axial load

Q: What role does the mass play in balancing the see-saw? (Hint: Would you need to balance the rigid…

A: The condition for equillibrium according to newtonian mechanics is,Net force on the object must be…

Q: An engineer wants to design a lightweight strong tie-rod as shown in figure 1. Consider a design…

A: 2.1) answer:

Q: Calculate the tension in the cable supporting the beam shown in the figure. If a plant weighing 100…

Q: In the figure, a homogeneous rod with mass m = 1.8 kg and length L rests on two scales. A…

Q: Which vial, left or right, contains a liquid in which its cohesive forces exceed its adhesive…

A: Cohesive Force is the one with acts between two particles which belongs to the same metal or the…

Q: A traffic light hangs from a pole as shown in (Figure 1). The uniform aluminum pole AB is 8.00 m…

Q: A heavy mirror that has a width of 1.00 m is to be hung on a wall as shown in (Figure 1). The mirror…

A: Analyze the free body diagram. Consider the upward direction to be positive and the downward…

Q: FIGURE 1 60 kN B 0.75 E :1.00 1.00. 1.00 25 kN

Q: What would be the maximum weight W of the block, shown in the following figure, so that the tension…

Q: A large advertisement board (W) is held in position by cable F1, with a breaking strength of 1500 N…

A: Given : breaking strength of the F1 is, 1500 N breaking strength of the F2 is, 750 N Determine :…

Q: In the figure, one end of a uniform beam of weight 130 N is hinged to a wall; the other end is…

Q: In the figure, one end of a uniform beam of weight 160 N is hinged to a wall; the other end is…

Q: The forces on the gusset plate of a joint in a bridge truss act as shown. Determine the value of P…

A: To maintain the equilibrium of the joint, the forces must follow the equilibrium conditions or…

Q: Based on this illustration, what must be the value of F1 to make the see-saw balanced? * F2 = 50N 3…

Q: Use: F1 = 22 N F1 F2 = 13 N 888 F2 F3 = 22 N 888 F4 =61 N F3 Determine the magnitude of the…

Q: In the figure below a crowbar is used to lift a weight. If a down ward force of 246 N is applied to…

Q: In the linear region of the Strain vs. Stress diagram is called Elastic Modulus * True False

Q: A student creates a beam bridge for a project, suspends masses from the bridge, and spans the bridge…

Q: If the beam attached to a hinge is 4 meters long and weighs 600 Newtons, and the sign weighs 400…

Q: In the figure, one end of a uniform beam of weight 120 N is hinged to a wall; the other end is…

A: Consider the free-body diagram of the beam, and the angle distribution.

Q: A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.069 m, and the…

A: Given,

Q: After an unfortunate accident occurred at a local warehouse, you were contracted to determine the…

Q: In the figure, one end of a uniform beam of weight 430 N is hinged to a wall; the other end is…

Q: After an unfortunate accident occurred at a local warehouse, you were contracted to determine the…

A: Given,mass of steel beam, λ = 81.70 kg per metertension in the cable, T = 12170 Nmaximum load, m =…

Q: If the beam attached to a hinge is 4 meters long and weighs 600 Newtons, and the sign weighs 400…

Q: After an unfortunate accident occurred at a local warehouse, you were contracted to determine the…

Q: A horizontal uniform plank is supported by ropes I and II at points P and Q, respectively, as shown…

A: In this case, there are three forces on the plank. The force T1 and T2 are pulling up respectively…

Q: In the figure, one end of a uniform beam of weight 100 N is hinged to a wall; the other end is…

A: Given data as per question Weight of the beam = 100 N angle = 290 Calculations As the beam is in…

Q: under curve 10. Which one of the following objects is in static equilibrium? A. В. С. D. а) А b) В C…

A: Required : Which object is in equilibrium.

Question

help

Determine the x and y components of F3 using scalar notation.
Express your answers using three significant figures separated by a comma.

Consider the gusset plate of a bridge truss shown in
(Figure 1). Suppose that F1 = 8 kN, F2 = 6 kN,
F3 = 4 kN , and F4 = 6 kN.
Figure
1 of 1
F2
F,
888
88

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Why are the cross sections of metal beams in the shape of the letter I instead of solid rectangles?
A traffic light hangs from a pole as shown in (Figure 1). The uniform aluminum pole AB is 8.00 m long and has a mass of 13.0 kg . The mass of the traffic light is 25.0 kg . Determine the tension in the horizontal massless cable CD. Determine the vertical component of the force exerted by the pivot A on the aluminum pole. Determine the horizontal component of the force exerted by the pivot A on the aluminum pole.
The graph below represent the tension-extension graph for a copper wire of length 1.2 m and cross sectional area 1.5 x 103m2. The tension is gradually increased from zero to a maximum value, and then reduced back to zero.
Two structural members B and C are bolted to bracket A . Knowing that both members are in tension and that P= 10 kN and Q= 15 kN, determine graphically the magnitude and direction of the resultant force exerted on the bracket using (a) the parallelogram law, (b) the triangle rule.
A 3500 kg statue is placed on top of a cylindrical object (Y= 2.3 x10^10 Pa). The stand has a cross sectional area of 0.073m^2 and a height of 1.8 m. Find the change in height of the object in meter.
Mr. Tanner’s construction class is studying the construction of roof trusses He taught them that the trusses must form two right triangles. Which of the following designs could be used as a roof truss?
You decide to cut an L-shaped object out of cardboard so that the object is in static equilibrium if hung as shown in (Figure 1). The vertical bar of the object has a width of x = 5.2 cm. Find the heigth of the horizontal bar.
Using the method of joints, determine the force in members AG and FB of the roof truss as shown in Fig. 1. State whether the members (AG and FB) are in tension or compression.
The horizontal beam in Fig. 1 weighs 150 N, and its center of gravity is at its center. Find (a) the tension in the cable and (b) the horizontal and vertical components of the force exerted on the beam at the wall.
The lintel of prestressed reinforced concrete in the figure below is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.10 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 47.5 cm2. Young's modulus for the concrete is 3.00 1010 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.45 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released(b) What is the new tension T2 in the rod?(c) The rod will then be how much longer than its unstressed length?(d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length?(e) Find the required original tension T1 in the rod.
A traffic light hangs from a pole as shown in (Figure 1). The uniform aluminum pole AB is 8.00 m long and has a mass of 10.0 kg . The mass of the traffic light is 25.0 kg . a)Determine the tension in the horizontal massless cable CD. b)Determine the vertical component of the force exerted by the pivot A on the aluminum pole. c)Determine the horizontal component of the force exerted by the pivot A on the aluminum pole.
A steel pin inserted into a wooden member hanging from the ceiling transmitsthe loads shown in the figure. Determine: a) The crushing stress experienced by the interface between the wood and the steel. b) The shear stress experienced by the steel pin. c) The shear stress experienced by the wood.