Computer science machine organization question Consider these instructions: ST, LDR, ADD, JSR, BR.a) Which instructions use ADDR2MUX?b) Which instructions use the register file?c) Which instructions use the ALU?d) Which instructions use the MEMORY?GateMARMUX AGatePCMARMUXLD.PC-PC+1REGDRPCMUXFILELD.REG-SR2SR2 OUTSRIOUT SRIZEXTADDRIMUXADDRIMUXA ADDR2MUX16100]SEXTSEXT[4:0][8:91SEXTASR2MUX/|15:9)SEXTFINITESTATERBMACHINEALUALUK16NZP-LD.CCLD.IR- IRLOGIC-GateALUGateMDR-16161616LD.MDR- MDRMEMORYMAR -LD.MARINPUTOUTPUT1616MEM.EN, R.W

This question is related to Computer architecture. I'll discuss one by one next step onwards.

Consider these instructions: ST, LDR, ADD, JSR, BR. a) Which instructions use ADDR2MUX? b) Which instructions use the register file? c) Which instructions use the ALU? d) Which instructions use the MEMORY? GateMARMUX GatePC MARMUX LD.IC PC REG DR PCMUX FILE LD.REG- SR2 SRI SR2- OUT ZEXT ADDRIMUX ADDRIMUX ADDR2MUX (100] SEXT SEXT |[4:0] 1801 SEXT ASR2MUX/ (15.9) FINITE 15:01 SEXT R STATE MACHINE ALU ALUK NZP-LD.CC LD.IR- LOGIC -GateALU GateMDRA 16 16 16 LD.MDR- MDR 16 MEMORY MAR -LD.MAR INPUT OUTPUT 16 MEM.ĖN, R.W

Consider these instructions: ST, LDR, ADD, JSR, BR. a) Which instructions use ADDR2MUX? b) Which instructions use the register file? c) Which instructions use the ALU? d) Which instructions use the MEMORY? GateMARMUX GatePC MARMUX LD.IC PC REG DR PCMUX FILE LD.REG- SR2 SRI SR2- OUT ZEXT ADDRIMUX ADDRIMUX ADDR2MUX (100] SEXT SEXT |[4:0] 1801 SEXT ASR2MUX/ (15.9) FINITE 15:01 SEXT R STATE MACHINE ALU ALUK NZP-LD.CC LD.IR- LOGIC -GateALU GateMDRA 16 16 16 LD.MDR- MDR 16 MEMORY MAR -LD.MAR INPUT OUTPUT 16 MEM.ĖN, R.W

Principles of Information Systems (MindTap Course List)

12th Edition

ISBN:9781285867168

Author:Ralph Stair, George Reynolds

Publisher:Ralph Stair, George Reynolds

Chapter3: Hardware: Input, Processing, Output, And Storage Devices

Section: Chapter Questions

Problem 3SAT: The time it takes to perform the fetch instruction and decode instruction steps is called the...

See similar textbooks

Similar questions

The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
What will be the contents of BX after the following instructions execute?mov bx,5stcmov ax,60hadc bx,ax
Assume the two instructions below are executed.AND R4, R4, #0STR R4, R7, #-1Which one of the statements below is correct? Group of answer choices The execution sets the value at memory address with label H to x1233. The execution sets the value in R4 to x400F. The execution sets the value at memory address with label H to x1234. The execution sets the value at memory address with label H to 0. The execution sets the value at memory address with label B to x1233.
Provide opcodes for the following MOV instructions:.datamyByte BYTE ?myWord WORD ?.codemov ax,@datamov ds,ax ; a.mov ax,bx ; b.mov bl,al ; c.mov al,[si] ; d.mov myByte,al ; e.mov myWord,ax ; f.
(a) Find the value of AX and EAX registers.dataarrayW WORD 7000h,8000h,9000harrayD DWORD 1,2,3,4.codemov ax,[arrayW+2] ; AX =mov ax,[arrayW+4] ; AX =mov eax,[arrayD+4] ; EAX =(b) write a program that adds the following three bytes:.datamyBytes BYTE 80h,66h,0A5h
The control signal Ep or iEnableoutput allows the program counter to decrement its value. True False The control signal Ep or iEnableoutput sends the content of the program counter to the W bus. True False A tri-state buffer is needed for all data going to the W bus. True False In using 'assign' statement in Verilog, the left hand side must always be a register. True False In declaring a register in Verilog, the following format must be followed: reg [LSB:MSB] identifier; True False
Provide opcodes for the following MOV instructions:.datamyByte BYTE ?myWord WORD ?.codemov ax,@datamov ds,axmov es,ax ; a.mov dl,bl ; b.mov bl,[di] ; c.mov ax,[si+2] ; d.mov al,myByte ; e.mov dx,myWord ; f.
Here are some registers and storage locations during the run of a program.For this example, all numbers are hex.eax contains 300ebx contains 3000The doubleword at memory location 300 contains 500The doubleword at memory location 10 contains 70 What is in eax after the command addl $10, %eax executes? a. 310 b. 510 c. 370
Which one of the following registers contains the address of the next instruction to be fetched from the memory? a. Memory Address Register (MAR). b. Program Counter (PC). c. Memory Buffer Register (MBR). d. Instruction Register (IR).
Answer the following questions based on the figure below.(a)Give the hexadecimal representation of “beq x10,x0,L1”.(bAssume the program executes to “jal x1,4”. What is the next instruction to execute? (c)Use lui or auipc to write a sequence of instructions to jump from the memory location 0x0000000020000000 to execute “beq x10,x0,L1” in the figure. Show the memory locations of your instructions and explain your code. You cannot use more than 3 instructions and can only use RV64I instructions.
From the given code from step 1-step19 a- What are the memory location addresses that will be accessed in memory data segment in this program? b- What is the content of each memory location accessed in memory data segment in this program? c- What does the content of each memory location refer to?
OBJECTIVETo perform the basic arithmetic and logical operations using the 8086 Microprocessor emulator. Take a screenshot of your code and output. 3. LOGICAL AND OPERATIONALGORITHMStep 1. Allocate some space for the result in data segmentstep 2. In code segment, store accumulator with some valuestep 3. Store B register with some valuestep 4. Perform AND operation on the register content with accumulatorstep 5. Result is stored in accumulatorstep 6. The result is stored in required memory location SAMPLE INPUTS & OUTPUTSBefore Execution: After Execution:AX = 0001H AX = 0001HBX = 0001H