Answered: Consider turbulent forced convection in…

Consider turbulent forced convection in a circular tube. Will the heat flux be higher near the inlet of the tube or near the exit? Why?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.43P: 7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s...

See similar textbooks

Related questions

Q: Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220°C flows in…

A: Given data: *The hot carbon dioxide is at 1 atm pressure. *The temperature of the gas is Tg=220°C.…

Q: Water is to be heated from 10°C to 80°C as it flows through a 2-cm-internal-diameter, 13-m-long…

A: The bulk mean temperature of the water, The properties of water at this temperature is given as,…

Q: Q) Water at 22'C flows in a 40-cm-diameter pipe and 25-m-long at an average velocity of 0.15 m/s.…

Q: What is the physical significance of the Fourier number? Will the Fourier number for a specified…

Q: What is natural convection? How does it differ from forced convection? What force causes natural…

A: Heat transfer can take place in three different modes namely conduction, convection and radiation.…

Q: c) Water is to be heated from 10°C to 80°C as it flows through a 2-cm-internal-diameter, 7-m- long…

A: here 2 question are there, both are not interlinked and as per honor code and answering guidelines…

Q: A long 10-cm-diameter steam pipe whose external surface temperature is 110°C passes through some…

A: In order to proceed with the problems some assumptions need to be considered. Steady operating…

Q: If q" w = 5000 and the convection heat transfer coefficient at the pipe outlet is 1000 W/m2K,…

Q: Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface…

A: Given data Temperature of hot engine oil To = 1500C = 423K Velocity of oil flow V = 2m/s Length of…

Q: An array of power transistors, dissipating 6W of power each, are to be cooled by mounting them on a…

Q: For air flow at a constant wall temperature of 100 ◦C and average bulk temperature of 40 ◦C through…

A: Tb=40°CV=0.8m/sD=4cm=0.04m h=?

Q: A 1.2-in-outer-diameter pipe is to span across a river at a 115-ft-wide section while being…

A: Given: The outer diameter of the pipe is D=1.2 in. The width of the river is W=115 ft. The average…

Q: b) A 0.4-W cylindrical electronic component shown in Figure Q3b with diameter 0.3 cm and length 1.8…

Q: The hot water needs of a household are to be met by heating water at 15°C to 95°C by a parabolic…

Q: The components of an electronic system are located in a 1.5-m-long horizontal duct whose cross…

A: given data Length of the pipe L = 1.5m Cross section area of the duct = 0.2*0.2 m2 Temperature of…

Q: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and 10-m-long wall of a…

Q: The components of an electronic system dissipating 180 W are located in a 4-ft-long horizontal duct…

A: The data given is Temperature inlet, Tin = 85°F Temperature inlet, Tout = 100°F Area of cross…

Q: Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat…

A: The data given is, The temperature of liquid Mercury = 250 ℃ The velocity of flow, V = 0.3 m/s…

Q: Air with ρ = 1,202 kg/m3 and ν =15.1 x 10-6 m2/s, is flowing steadily in a duct shown in Figure 1…

Q: Liquid water enters a 10-m-long smooth rectangular tube with a -50 mm and b = 25 mm. The surface…

A: Given: The length of tube, L = 10 m The width of tube, a = 50 m The height of tube, b = 25 mm The…

Q: What is the physical significance of the Reynolds number? How is it defined for external flow over a…

A: Given: Plate with length L To find; Significance of Reynolds number Reynolds number for external…

Q: When is heat transfer through a fluid conduction and when is it convection? For which case is the…

A: The rate of heat transfer is given

Q: The hot water needs of a household are to be met by heating water at 15°C to 95°C by a parabolic…

A: Entry temperature = 15 C Exit temperature = 95 C flow rate = 1.8 kg/s Diameter = 4 cm Net…

Q: Q4/A long aluminum wire of diameter 3 mm is extruded at a temperature of 370°C. The wire is…

Q: What regime favors heat transfer and why? Laminar, Turbulent or Transitional

A: Heat transfer is basically a process in which the molecules are moved from their initial position in…

Q: A 1.2-in-outer-diameter pipe is to span across a river at a 140-ft-wide section while being…

A: Given data as per question Diameter of pipe =1.2 in Flow velocity = 10ft/s

Q: Q4) Water is to be heated from 10°C to 80°C as it flows through a 2-cm-internal-diameter, 7-m-long…

Q: Air is flowing in parallel over the upper surface of aflat plate with a length of 4 m. The first…

A: The properties of air at 30 degree Celsius are: The local Reynolds number can be calculated as,…

Q: Consider the flow of oil at 20oC in a 40-cm-diameter pipeline at an average velocity of 0.5 m/s. A…

Q: The components of an electronic system are located in a 1.8-m-long horizontal duct whose cross…

A: Given:- Ts=65 T∞=30 k=0.02717W/m.k v=1.744*10-5m2/s Pr=0.72345 V=200m/min D=20cm To Find:- The total…

Q: Water at an average temperature of 180°F and an average velocity of 4 ft/s flows through a…

A: According to the question water is at a temperature of 180 oF . Write the values of conduction heat…

Q: What does the Grashof number represent? How does the Grashof number differ from the Reynolds number?

A: Grashof number is a dimension less number. Which we use in heat transfer and fluid mechanics.

Q: Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a…

A: Given Data Inlet temperature is :T1=500 K Outlet temperature is : T2=600 K Mass flow rate is :…

Q: An array of power transistors, dissipating 6 W ofpower each, are to be cooled by mounting them on a…

A: Given: The power dissipating by a single transistors, Q = 6 W The area of the square aluminum plate,…

Q: An average man has a body surface area of 1.8 m2 and a skin temperature of 330C. The convective…

A: Let A = Surface area of man body =1.8m2 V =1.2m/s h =Heat Transfer Coefficient =8.6XVX0.53 h…

Question

Consider turbulent forced convection in a circular
tube. Will the heat flux be higher near the inlet of the tube or
near the exit? Why?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
What does the logarithmic mean temperature difference represent for flow in a tube whose surface temperature is constant? Why do we use the logarithmic mean temperature instead of the arithmetic mean temperature?
Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?
In the effort to find the best way to cool a smooth thin-walled copper tube, an engineer decided to flow air either through the tube or across the outer tube surface. The tube has a diameter of 6 cm, and the surface temperature is maintained constant. Determine the convection heat transfer coefficient when air is flowing through a thin-walled tube at 25 m/s with bulk mean temperature of 50°C. _____ w/m^2k
Consider a 25-mm-diameter and 15-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 50°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet temperature of 150°C.
Combustion gases passing through a 5-cm-internal-diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 225 kPa and 250oC at a mean velocity of 2.5 m/s, and leave at 150o If the average heat transfer coefficient is 150 W/m2K and the inner surface temperature of the tube is 110oC, determine (a) the tube length and (b) the rate of evaporation of water.
Water is to be heated from 10°C to 80°C as it flows through a 2-cm-internal-diameter, 13-m-long tube. The tube is equipped with an electric resistance heater, which provides uniform heating throughout the surface of the tube. The outer surface of the heater is well insulated, so that in steady operation all the heat generated in the heater is transferred to the water in the tube. If the system is to provide hot water at a rate of 5 L/min, determine the power rating of the resistance heater. Also, estimate the inner surface temperature of the pipe at the exit.
What does the Grashof number represent? How does the Grashof number differ from the Reynolds number?
The components of an electronic system are located in a 1.5-m-long horizontal duct whose cross section is 20 cm * 20 cm. The components in the duct are not allowed to come into direct contact with cooling air, and thus are cooled by air at 30°C flowing over the duct with a velocity of 200 m/min. If the surface temperature of the duct is not to exceed 65°C, determine the total power rating of the electronic devices that can be mounted into the duct.
A steam pipe having a surface temperature of 200C passes through a room where thetemperature is 27C. the outside diameter of pipe is 80mm and emissivity factor is 0.8. Calculatethe radiated heat loss for 3 m pipe length.
Combustion gases passing through a 3-cminternal- diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 115 kPa and 250°C at a mean velocity of 5 m/s, and leave at 150°C. If the average heat transfer coefficient is 120 W/m2?K and the inner surface temperature of the tube is 110°C, determine (a) the tube length and (b) the rate of evaporation of water.
Air with ρ = 1,202 kg/m3 and ν =15.1 x 10-6 m2/s, is flowing steadily in a duct shown in Figure 1 that is made of stainless steel. To maintain the flow under laminar, determine the following; 1.1 the maximum airflow rate, and 1.2 the fan power required to overcome the pressure losses in this section of the duct.