Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 7, Problem 7.43P
Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Liquid glycerin is flowing through a 25-mm-diameter and 10-m-long tube. The liquid glycerin enters the tube at 10°C with a mass flow rate of 0,2 kg/s. If the outlet mean temperature is 60°C and the tube surface temperature is constant, determine the surface temperature of the tube.
Consider a 25-mm-diameter and 15-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 50°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet temperature of 150°C.
Combustion gases passing through a 5-cm-internal-diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 225 kPa and 250oC at a mean velocity of 2.5 m/s, and leave at 150o If the average heat transfer coefficient is 150 W/m2K and the inner surface temperature of the tube is 110oC, determine (a) the tube length and (b) the rate of evaporation of water.
Chapter 7 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .arrow_forwardOne house owner with a pond on his property has decided to use the pond water to cool his house. His idea is to flow air through a thin smooth 10-cm-diameter copper tube that could be submerged into the pond. The water in the pond, at few meters below the surface is typically maintained at a constant temperature of 15°C. If he assumes the air (~1 atm) entering the copper tube at a mean temperature of 30°C with an average velocity of 2.5 m/s, determine the necessary copper tube length that would be needed so that the outlet mean temperature of the air is 20°C. You may consider the convection heat transfer coefficient of 1000 W/m2·K on the outer surface of the copper tube, between the pond water and copper tube. Since the copper tube is thin, the conduction resistance of the tube wall may be neglected.arrow_forwardIn a manufacturing plant that produces cosmetic products, glycerin is being heated by flowing through a 25-mm-diameter and 10-m-long tube. With a mass flow rate of 0.5 kg/s, the flow of glycerin enters the tube at 25°C. The tube surface is maintained at a constant surface temperature of 140°C. Determine the outlet mean temperature and the total rate of heat transfer for the tube. Evaluate the properties for glycerin at 30°C.arrow_forward
- Consider turbulent forced convection in a circular tube. Will the heat flux be higher near the inlet of the tube or near the exit? Why?arrow_forwardWhat does the logarithmic mean temperature difference represent for flow in a tube whose surface temperature is constant? Why do we use the logarithmic mean temperature instead of the arithmetic mean temperature?arrow_forwardWater with a mass flow rate of 0.002 kg/s at 18oC flows inside a tube while the flow is already developed hydrodynamically. The inner diameter of the tube is 1.5 cm, and the inner pipe wall temperature is maintained uniformly at 125oC. Calculate the required tube length to increase the water temperature to 82oC.arrow_forward
- Liquid mercury is flowing at 0.9kg/s through a 5-cm diameter tube with inlet and outlet mean temperatures of 100°C and 200°C, respectively. The tube surface temperature is maintained constant at 250°C. Determine the tube length using the Dittus-Boelter equation, in m. ______ marrow_forwardAir with ρ = 1,202 kg/m3 and ν =15.1 x 10-6 m2/s, is flowing steadily in a duct shown in Figure 1 that is made of stainless steel. To maintain the flow under laminar, determine the following; 1.1 the maximum airflow rate, and 1.2 the fan power required to overcome the pressure losses in this section of the duct.arrow_forwardCombustion gases passing through a 3-cminternal- diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 115 kPa and 250°C at a mean velocity of 5 m/s, and leave at 150°C. If the average heat transfer coefficient is 120 W/m2?K and the inner surface temperature of the tube is 110°C, determine (a) the tube length and (b) the rate of evaporation of water.arrow_forward
- Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b = 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C.arrow_forwardConsider a 25-mm-diameter and 15-m-long smooth tube that is used for heating fluids. The wall is heated electrically to provide a constant surface heat flux along the entire tube. Fluids enter the tube at 50°C and exit at 150°C. If the mass flow rate is maintained at 0.01 kg/s, determine the convection heat transfer coefficients at the tube outlet for water, engine oil, and liquid mercury.arrow_forwardConsider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license