Consider two liquids of densities p₁ = 1000 kg/m³ and p₂ = 800 kg/m³ that are initially flowing in pipe1 and pipe2, respectively. The two flow streams are mixed when they merge into the horizontal pipe3 as shown in the figure. The flow rates in the three pipes are Q₁ = 10-2 m³/s, Q₂ = 2.5x10-3 m³/s and Q3 = 1.25x10-2 m³/s and the viscosities of all three fluids are equal: μ₁ = μ₂ = μ3 = 5.1x10-4 Pa.s. Q1 Q2 Pipe2 Pipel The flow in pipe3 is laminar True False Pipe3 Q3

Consider two liquids of densities p₁ = 1000 kg/m³ and p₂ = 800 kg/m³ that are initially flowing in pipe1 and pipe2, respectively. The two flow streams are mixed when they merge into the horizontal pipe3 as shown in the figure. The flow rates in the three pipes are Q₁ = 10-2 m³/s, Q₂ = 2.5x10-3 m³/s and Q3 = 1.25x10-2 m³/s and the viscosities of all three fluids are equal: μ₁ = μ₂ = μ3 = 5.1x10-4 Pa.s. Q1 Q2 Pipe2 Pipel The flow in pipe3 is laminar True False Pipe3 Q3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows at the rate of 0.80m3/s in a 900-m long pipe. The total head loss in the pipe is 4m. Which of the following most nearly gives the diameter of the pipe using the Darcy-Weisbach formula with f = 0.018?
Determine the available suction head of the pump that is taking a gasoline at 204°C at a closed tank with a pressure 585 kPa gauge. the specific gravity of gasoline is 0.78 and it’s vapor pressure is 620 kPa absolute. the loss in suction pipe is 0.60 m and the pump center line is located 3.60 m above the gasoline level A. 8.66m B. 3.67m C. 7.66m D. 4.47m
3. What is the volumetric flow rate between two plates if the top plate is pulled, while keeping the bottom plate stationary, and simultaneously imposing pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel.
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Water at 65 degrees Celsius is flowing horizontally at a rate of 84.1 m^3/hr in a pipe. It enters a 150-mm 90 degree elbow and is diverted upwards into a connecting pipe. The diameter of the outlet is 85mm. If the pressure just before the elbow is 95 kPa, determine the magnitude and direction of the force necessary to keep the elbow in place. Assume frictional losses in the elbow are negligible.
SAE 30 oil at 20°C flows in the 2.5-cm-diameter pipe as shown in the figure below, which slopes at 37°. For SAE 30 oil, take ρ = 891 kg/m3 and μ = 0.29 kg/m⋅s. Determine the flow rate in m3/h. The flow rate is m3/h.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
Neglecting head losses, determinewhat horsepower the pump must deliver toproduce the flow as shown. Here theelevations at points A, B, C, and D are 110 ft.200 ft, 110 ft and 90 ft, respectively. The nozzle area is 0.10 ft2
Write legibly 6. The piping shown in the figure is a parallel-pipe system carrying water at normal temperature. Pressure head at junction X is 76 m, while that at Y is 48 m. If the inflow at junction X is 0.35 cum/s, determine the flow of water at each branch of the loop. Assume C = 120 for all pipes. determine: a. flow in pipe A: ____________m3/s 1b. flow in pipe B: ____________ m3/s c. flow in pipe C: _____________ m3/s
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
According to Torricelli´s theorem, the velocity of a fluid discharging through the hole of a reservoir is V=(2gh)^1/2, where h is the height of water above the hole, as shown in the figure. If the hole has a section Ao and the reservoir is cylindrical with a cross-section of area Ab>>Ao. Obtain a formula for the time it will take for the reservoir to completely empty if the initial height of the water is ho.
The water jet exiting from a stationary tank through a circular opening of diameter 300 mm impinges on a rigid wall as shown in the figure. Neglect all minor losses and assume the water level in the tank to remain constant. The net horizontal force experienced by the wall is KN. Density of water is 1000 kg/m³. Acceleration due to gravity g = 10 m/s².