Consider two systems, one at a constant temperature t and the other at a constant temperature T (t > T). Allow the two systems to come into contact and be thermally insulated from each other but not from their surroundings. Energy will flow from system A to system B because of System System Temperature Temperature Select one: O a. Mass difference O b. Volumetric difference O C. Temperature difference O d. Energy difference

Consider two systems, one at a constant temperature t and the other at a constant temperature T (t > T). Allow the two systems to come into contact and be thermally insulated from each other but not from their surroundings. Energy will flow from system A to system B because of System System Temperature Temperature Select one: O a. Mass difference O b. Volumetric difference O C. Temperature difference O d. Energy difference

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a. A fan is to accelerate quiescent air to a velocity of 10m/s at a rate of 4 m3/s. Determine the minimum power thatmust be supplied to the fan. Take the density of air to be 1.18kg/m3. b. A classroom that normally contains 40 people is tobe air-conditioned with window air-conditioning units of 5-kW cooling capacity. A person at rest may be assumed todissipate heat at a rate of about 360 kJ/h. There are 10 lightbulbs in the room, each with a rating of 100 W. The rate ofheat transfer to the classroom through the walls and the windows is estimated to be 15,000 kJ/h. If the room air is to bemaintained at a constant temperature of 21°C, determine thenumber of window air-conditioning units required c. A vertical piston–cylinder device contains water andis being heated on top of a range. During the process, 65 Btu of heat is transferred to the water, and heat losses from theside walls amount to 8 Btu. The piston rises as a result ofevaporation, and 5 Btu of work is done by the vapor.…
Determine the MW and specific heat ratio of a gas whose Cv=1.386 kJ/kg.K and R= 0.485 kJ/Kg.K
Warm air is contained in a piston-cylinder assembly oriented horizontally. The aircools slowly from an initial volume of 0.003 m 3 to a final volume of 0.002 m 3 . Duringthe process, the spring exerts a force that varies linearly from an initial value of 900 Nto a final value of zero. The atmospheric pressure is 100 kPa, and the area of thepiston face is 0.018 m 2 .Friction between the pistonand the cylinder wall can beneglected. For the air in thepiston-cylinder assembly,determine the initial and finalpressures, each in kPa andatm.
Air with mass of 16 kg is heated at constant gage pressure of 9044 hPa from -24.0 °C to 184 °C. Determine the heat required in MJ. and the change of system volume
. Show that the law of the adiabatic process is given byPV ˠ = constantWhere: (ˠ) is the ratio of specific heat capacities.
Is the work done by the system positive, negative, or zero during an adiabaticprocess where the final temperature is higher than the initial temperatureCan pdV work be done on the system during an isobaric process? What aboutduring an isochoric process?Compare and contrast the concepts of work and heat. What is the difference?
A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 285 psf, and 270 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,255 psf and 750 degrees Fahrenheit. Assuming that the velocity found at the inlet is 6,285 feet per minute and the Heat supplied is 580 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 6 minutes?
A 0.75-m3rigid tank initially contains air whose density is 1.18 kg/m3 The tank is connected to a high-pressure supply line through a valve. The valve is opened, and air is allowed to enter the tank until the density in the tank rises to 4.95 kg/m3. Determine the mass of. air that has entered the tank.
A fireman is using high pressure stream of water from hose to combat ragingforest fire. At one end the hose has inside diameter of d1= 5cm ad is connectedto high pressure water reservoir at P1=300psi. At the other end is nozzle withdiameter d2=3cm that is exposed to atmospheric pressure P2=1atm.To a good approximation, flowing water in this process can be modelled ashaving a constant temperature and constant mass density =1g/cc. Moreover,for an incompressible liquid, the following equation well describes isothermalenthalpy changes.delta h= v. delta PWhere v is volume per mole or molecule (depending on the basis of h)1) How much faster is the velocity of exiting water at the nozzle than that ofthe entering stream at the reservoir? Express your answer as ratio.2) If hose is well insulated, find the exit velocity of stream of water, in m/s3) Find the exit volumetric flowrate of water, in gal/s
An automobile engine consumes fuel at a rate of 22 L/h and delivers 55 kW of power to thewheels. If the fuel has a heating value of 44,000 kJ/kg and a density of 0.8 g/cm3, determinethe efficiency of this engine. Hint, Qa= mass of fuel * heating value.
Solve for the latent heat of water at Tw = 28C(and. λw = 2435 kJ/kg)
heat transfer question is image