= constant d Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. 근 شكر الحائر 27 B ADA 400 mm PA 29.43 N/cm 2A =28 m Dg= 400 mm Pe = 22.563 N/cm Z₁ = 30 m DATUM LINE

= constant d Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. 근 شكر الحائر 27 B ADA 400 mm PA 29.43 N/cm 2A =28 m Dg= 400 mm Pe = 22.563 N/cm Z₁ = 30 m DATUM LINE

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the pumping system shown below, determine the following. a. Head loss at suction in m b. Head loss at discharge in meters c. Total head losses in meters d. Total dynamic head developed by the pump in meters e. Water Power in KW f. Brake Power in KW g. Energy consumption for 15 hours operation in KW-hr h. Line current drawn by the 3-Phase motor drive in amperes i. Pumping cost in Pesos/Day if electricity costs P7.00/KW-hr Figure: Other Data Water Temperature: 20∘C Suction Line 5−20 m 1−90∘ Elbow 1− Check Valve (Fully Open) Pipe Material: Galvanized Iron ND=100 mm Discharge Line L=50 m 12−90∘ Elbow 1− Gate Valve (Fully Open) 1− Check Valve Pipe Material: Galvanized Iron ND =80 mm Pump Efficiency: 75% Motor Efficiency: 82% Volts: 220 V Power Factor: 92%
6. Water is flowing through a pipe having diameter 300mm and 200 mm at the bottom and upper end respectively. The pressure at the lower(bigger) end is 25 N/cm2 and the pressure at the upper end is 10 N/cm2. Determine the difference in datum head if the rate of flow through pipe is 40 lit/s.
The diameter of a pipe carrying oil(s=0.92) changes gradually from 400 mm at A to 600 mm at B. Point A is 3.6 m lower than B. If the pressure at A is 70 KPa and that at B is 49 KPa when 140 L/s is flowing, determine the direction of flow; (b) the frictional loss between the two points.
The water is flowing through a taper pipe of length 100 m having diameters 600 mm at the upper end and 300 mm at the lower end, at the rate of 60 litres/s. The pipe has a slope of 1 in 40. Find the pressure at the lower end if the pressure at the higher level is 22 N/ cm².
The head-discharge characteristic relationship of a pump is given by:H = 40 - 200*Q^2, where H is the total head generated by the pump in meters and Q is the discharge in m^3/s. The pump lifts water through a pipe 0.3 meter diameter over a distance of 1000 meters against a static lift of 25 meters. Find the operating/ duty point (H and Q) if the friction coefficient of the pipe 'f ' is 0.03.
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.67 cm and the other end is 0.29 cm. The larger and smaller ends are located 9 m and 3 m, respectively, from the datum line. If the flow at the 9 m datum line is 1.48 m/s and the pressure is 5156 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
A pump delivers water, density =1000kg/m3, at a volume flow rate of 0.004256 m3/sec. If the head developed by the pump is 4.01 m, determine the fluid power in Watts. Take g=9.81 m/s2. State the answer to two decimal places.
Determine the available suction head of the pump that is taking a gasoline at 204°C at a closed tank with a pressure 585 kPa gauge. the specific gravity of gasoline is 0.78 and it’s vapor pressure is 620 kPa absolute. the loss in suction pipe is 0.60 m and the pump center line is located 3.60 m above the gasoline level A. 8.66m B. 3.67m C. 7.66m D. 4.47m