W (continuation)What concentrated load at C will result to the given shear?O 11.5O 10.5O 12.0O 10.0(continuation)What is the reaction at the left support A?O 12.010.0O 11.5O 10.5 SITUATION.Refer to the figure.CD田由田由bV = 10.5V = 0.5V -11.5The shear diagram due to loads on a simply supported beam is plotted as shown.Given:a = 3 mb = 6mC = 3 mHow much is the maximunm span moment?O 23.033.034.531.5

Span loading arrangement and shear force diagram is given and it has been asked to determine left…

Answered: (continuation) What concentrated load…

(continuation) What concentrated load at C will result to the given shear? O 11.5 O 10.5 12.0 O 10.0 (continuation) What is the reaction at the left support A? O 12.0 O 10.0 O 11.5 O 10.5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A water tank made from a steel having a thickness of 12mm has the following dimensions. Internal Dia...

Q: A 1.25 m layer of the soil (Gs = 2.65 and porosity = 35%) is subject to an upward seepage head of 1....

Q: What is the bouyant force on the cylinder(kN)? Determine the tension in the cable if the top of the ...

A: Buoyant Force= Weight of fluid displaced Weight of fluid displaced = Density * 9.81* Volume of water...

Q: SITUATION: In accordance with Boussinesq theory, the vertical stress at a point below the center of ...

Q: Determine the absolute pressure inside a closed tank with a vacuum pressure of 67 kPa. Assume standa...

A: Given, Vacuum pressure(gauge pressure)= 67kpa, Standard atmospheric pressure at sea level = 101.3kpa...

Q: SITUATION: Water flows through an almost level rectangular channel 3 m wide at 12 m^3/sec. The depth...

Q: Refer to the figure shown a = 23 x 10°/°C E = 70 GPa A = 900 mm² -6 a = 11.7 x 10/°C E = 200 GPa %3D...

A: Given data For member-AB α1 = 11.7 × 10-6 /°C E1 = 200 GPa = 2 × 105 N/mm2 A1 = 1200 mm2 LAB = 300 m...

Q: The influence line for the vertical reaction at C for the beam shown is B D 7 m- - 7 m- -4 m- O a. 1...

Q: What is the significance of architecture?

A: Architecture: The study of buildings and various techniques required for the construction of buildin...

Q: 7. The following table shows traffic flow data collected at the main road in an urban area, in two s...

A: a) Calculate the peak hour factor by using formula as given as, PHF=VH4×V15 max Where, VH=Hourly vol...

Q: 500KN A 200mm 100mm C 45°

Q: If a beam is supported by fixed support at both its end then point of inflection will lie at what di...

Q: = Find the centroid of the next shaded area. 6m

Q: SITUATION: A 3-layer soil has the following properties from top to bottom: Estimate the rate of flow...

Q: SITUATION. Refer to the figure. A bin holds a cylinder as shown. Each cylinder weighs 800 kN and has...

A: Question number 2 and 3 are different questions and is not a part of the three cylinders question. Y...

Q: Problem 1: A rectangular magnesium bar having a cross section width of 4.8mm and its length is six t...

Q: Draw the shear and moment diagram. Then answer the questions: (1) What is the maximum shear? (2) W...

A: To Determine The maximum shear? The maximum moment?

Q: 1. For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the...

Q: 5. The solid shaft that is fixed connected at both ends has a diameter of 20 mm and a total length o...

Q: The solid 1.45-in.-diameter rod is subjected to a uniform axial distributed loading along its length...

Q: Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m³/s. At a point A in the pipe the...

Q: A uniformly distrubuted load applied on a strip fooing constructed in sand. Based on Hansen's equati...

Q: 120 mm 0mm II 20 mm 300mm

A: In mathematics and physics, the centroid or geometric center of a plane figure is the arithmetic mea...

Q: Find the moment (N-m) about point O. Each square is 1 m. on each side. F1 = 58 N F2 = 215 N C1 = 202...

A: To find moment about point O

Q: The solid 1.55-in.-diameter rod is subjected to a uniform axial distributed loading along its length...

Q: SITUATION: A footing, 2m x 3m in plan and 0.50m thick, is designed to support a 0.60m square column....

Q: Assuming that the live loads are transmitted to the bottom chords of the truss, the influence line f...

Q: For the beam shown, the magnitude of the distributed load is wo - 10.2 kN/m and the beam length is L...

A: Given data:

Q: Find the moment (N-m) about point O. Each square is 1 m. on each side. F1 = 157 N F2 = 247 N C1 = 10...

Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the larg...

Q: SITUATION: A finite slope has a height of 9m and it makes an angle of 30 degrees with the horizontal...

Q: Determine the reactions at the support. 3 kN -2 m 2 kN. 1.5 m 2 kN 1.5 m A B Ax=4kN, Ay=4.5kN, By=4....

Q: Classify the different types of traffic signs and mention the general objective of each type of sign...

Q: subjected to stress, it breaks with little elastic deformation and without significant plastic defor...

A: 1. True 2.false 3.false Eplanation -A material is brittle if, when subjected to stress, it fractures...

Q: Determine the magnitude of force, F (kN), if the resultant of the vectors shown in the figure is 67 ...

Q: .A 50-m tape weighs 2 kg. Every time a measurement is performed, the tape is supported at its end po...

Q: The common tangent AB of a compound curve is 76.42-m, with an azimuth of 88°30'. The vertex V being ...

Q: A rectangular channel 12 m wide carries 27.44 m3/s. The slope of the channel bed is 0.00283. Upstrea...

Q: The following perpendicular offset were taken from a chain line to the irregular boundary. Chainage ...

A: Given, Common distance= d= 30m Following offsets,

Q: A solid circular bronze [G- 6,500 ksi] shaft, 5.4 ft long and 1.125 in. in diameter, carries a torqu...

Q: Two couple forces and one moment act on the pipe assembly shown below. Find: (1) MRijk, the resultan...

A: Given Data -

Q: 500KN 200mm 100mm C 450 P

Q: plymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E 29,000 ksi; ...

Q: 1. For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the...

A: Given That -

Q: Provide various reasons as to why project costs may exceed the estimate and provide an alternative s...

A: Exceedance in the estimated amount of project is known as cost overrun. It is defined as the total a...

Q: If the bucket and its contents have a total weight of 191lb, determine the force in the supporting c...

Q: The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner ...

Q: 2. The lap joint that is 130 mm wide and 25 mm thick is connected by three 20-mm-diameter rivets. As...

A: Given, d=20 mm Number of rivet n=3 Allowable shear stress = 65 MPa Bearing stress =45 MPa Maximum te...

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown...

Q: Explain the significance of sampling as the most important step in assuring the quality of the aggre...

A: Sampling is maybe the main advance in assuring that great quality aggregates are being utilized. S...

Question

(continuation)
What concentrated load at C will result to the given shear?
O 11.5
O 10.5
O 12.0
O 10.0
(continuation)
What is the reaction at the left support A?
O 12.0
10.0
O 11.5
O 10.5

SITUATION.
Refer to the figure.
C
D
田由
田由
b
V = 10.5
V = 0.5
V -11.5
The shear diagram due to loads on a simply supported beam is plotted as shown.
Given:
a = 3 m
b = 6m
C = 3 m
How much is the maximunm span moment?
O 23.0
33.0
34.5
31.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data and to determine

VIEW

Solution and explanation

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Interior finishes for wood light frame construction

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the Vertical component (y-component) reaction force at support C? A. 600N, ( + ) upward B. 200N, (+) upward C. 600N,(-) downward D. 200N,( - ) downward SHOW SOLUTIONS
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
A simply-supported beam, 9 m in length, pin at A and roller at B, is subjected to a uniform load of 20 kN/m applied at the beam's middle third. Determine the slope of B wrt A, slope of A wrt B, tangential deviation of A wrt B, and the tangential deviation of B wrt to A. 3
A 6m simply supported beam AB carries 2 concentrated downward loads of P=60KN each placed at third points of the beam span. With constant EI=21000 KN-m2. Using Double Integration Method (DIM) with origin taken at point A (left support) where 0 ≤ x ≤ 6m, calculate the slope at the left support A? Express your answer in "degrees" in 3 decimal places. Take note that 180 degrees = pi radians.
W= 1317 kN/mUsing Slope Deflection Method, determine all reactions at supports also, determine shear andbending moments with complete labels. Use |=1/12 bh^3 and E = 2.15x10^7 KPa
PROBLEM 03In figure 03, determine the following.components of force P=150KN:a. Normal and Tangential components with.respect to the inclined surface,b. Rectangular components, andc. Components along with a’-axis (blue line),.and b’-axis (green line).
6. A simply supported beam carries a concentrated load of 24 kN at 6 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees. ROUND OFF TO FIVE DECIMAL PLACES.
Applying the (AMM) Area Moment Method Approach. Consider 150 mm x 200 mm section and E = 80 GPa. Round off to two decimal places a. Vertical Reaction at C in kN.b. Slope of the elastic curve at support C in degrees.c. Deflection at point B in mm.d. Deflection at point D in mm. Show organized solutions
Determine the bending moment 2.25 m to the right of point A for the beam shown below if P = 1705 N, T = 3205 Nm, a = 0.95 m, b = 0.97 m, and c = 1.15 m. Round of the final answer (in N m) to four decimal places
A prismatic continuous beam is shown. The flexural rigidity is 100 000 N. m². The problem maybe solve using superposition method. 1. Determine the vertical midspan deflection due to the given loads in millimeters if the middle support is removed. a. 5.83 b. 6.20 c. 4.95 d. 7.17 2. Determine the vertical midspan deflection due to an upward unit load at midpoint in millimeters if the middle support is removed. a. 0.513 b. 0.678 c. 0.245 d. 0.360 3. Determine the reaction at the middle support in Newton’s. a. 29.5 b. 13.8 c. 36.2 d. 47.0