If the bucket and its contents have a total weight of 191lb, determine the force in the supporting cable DA.(Figure 1). Express your answer to two significant figures and include the appropriate units. HA FDA = Value Units Submit My Answers Give Up Part B If the bucket and its contents have total weight of 19lb , determine the force in the supporting cable DB. Express your answer to two significant figures and include the appropriate units. HA gure 1 of 1 FDB = Value Units 25 ft Submit My Answers Give Up 4.5 3 ft Part C A If the bucket and its contents have total weight of 191lb, determine the force in the supporting cable DC. 1.5 ft Express your answer to two significant figures and include the appropriate units. Fpc = Value Units

If the bucket and its contents have a total weight of 191lb, determine the force in the supporting cable DA.(Figure 1). Express your answer to two significant figures and include the appropriate units. HA FDA = Value Units Submit My Answers Give Up Part B If the bucket and its contents have total weight of 19lb , determine the force in the supporting cable DB. Express your answer to two significant figures and include the appropriate units. HA gure 1 of 1 FDB = Value Units 25 ft Submit My Answers Give Up 4.5 3 ft Part C A If the bucket and its contents have total weight of 191lb, determine the force in the supporting cable DC. 1.5 ft Express your answer to two significant figures and include the appropriate units. Fpc = Value Units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For 20 pts., identify the beam reactions. Show complete solution and FBDs.
Base on the gravity load path shown above, explain what is occurring at each of the labeled points.
Please exapline to me how to solve this live loads! ~
PROBLEM 2: The barge shown supports the loads w1 and w2. Given: w1 = 250 kN/m, w2 = 500 kN/m, L1 = 2 m, L2 = 4 m, and L3 = 2 m. [4] Determine the magnitude of resultant of the loads w1 and w2 only. (ANSWER: 1500 KN) [5] Determine the location of the resultant of w1 and w2 only, measured from A. (ANSWER: 5 m) [6] Determine the required length, L, of the barge so that the upward pressure is uniform. (Hint: location of resultant of q must coincide with resultant of w1 and w2) (ANSWER: 10 m)
A hollow cylinder 1.20 m in diameter 2.5 m high weighs 4 kN.a. Determine the weight of lead anchor fastened at the bottom of thecylinder to make it float vertically in water with 0.5m projecting abovethe water surface.b. If the lead anchor is instead placed inside the cylinder, determine itsweight to keep the cylinder float vertically with 0.5 m projecting abovethe water surface.
You have design the base slab of a hydraulic structure use. After the design, you observed that there was a lot shear force near the piers, how would you provide shear reinforcement around the piers to sustain the structure?
A 30m tape weighing 0.035kg/m is constantly supported at mid length and at its end points with a steady pull of 5.60kg. What is the sag correction of the whole tape?
Load Balancing Method
Analysis/Design of Eccentrically Loaded Columns Using Interaction Diag. (35 pts-) Using the ACI column interaction graphs, select reinforcing for the short round spiral column shown in figure 2 iffc = 4000 psi, fy = 60,000 psi, Pu = 500 k, and Mu = 225 ft—k. In order to get fiJll credit print the interaction diagram(s) and clearlyr show your pg selection- Show your final results on a sketch.
Base on the gravity load path of the one-way system shown above, explain what is occurring at each of the labeled points.
A short hollow cast iron column of external diameter 30 cm and internal diameter 28 cm is filled with concrete. The column carries a total load of 400 kN. If ECI = 150 GPa and EConc =25 GPa, calculate: (a.)The stress in cast iron and concrete. (b.)What must be the internal diameter of the cast iron column if a load of 450 kN is to be carried and stresses and external diameter of the column remain unchanged?
Identify all the forces applied in the FBD. show complete FBD and solution. 30 mins left.