Control charts for X-bar and Range (R.) are maintained on the resistance in ohms of electrical part. The size of the samples is 5. After 6 samples, the sum of all samples means is 2046.5 ohms and the sum of all samples Ranges is 17.4 ohms. Lower control limits of R and X-bar, respectively are Select one: a. O and 339.4 b. 6.12 and 339.4 c.O and 342.76 d. 0 and 410.97 e. O and 407.63

Control charts for X-bar and Range (R.) are maintained on the resistance in ohms of electrical part. The size of the samples is 5. After 6 samples, the sum of all samples means is 2046.5 ohms and the sum of all samples Ranges is 17.4 ohms. Lower control limits of R and X-bar, respectively are Select one: a. O and 339.4 b. 6.12 and 339.4 c.O and 342.76 d. 0 and 410.97 e. O and 407.63

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

In repetitive operations it is often possible to automatically check for quality and then reject parts thatare unacceptable. In those situations, does that mean that control charts arent needed? Explain
Design specifications require that a key dimension on a product measure 100 ± 10 units. A process being considered for producing this product has a standard deviation of four units.a. What can you say (quantitatively) regarding the process capability?b. Suppose the process average shifts to 92. Calculate the new process capability.c. What can you say about the process after the shift? Approximately what percentage of the items produced will be defective?
Specifications for a metal shaft are much wider than the machine used to make the shafts is capableof. Consequently, the decision has been made to allow the cutting tool to wear a certain amountbefore replacement. The tool wears at the rate of .004 centimeter per piece. The process has a naturalvariation, σ, of .02 centimeter and is normally distributed. Specifications are 15.0 to 15.2 centimeters.A three-sigma cushion is set at each end to minimize the risk of output outside of the specifications.How many shafts can the process turn out before tool replacement becomes necessary?
A data entry clerk entered the incorrect part number for a blender. The part number was the part number for toasters. The best control to detect this error would include a(n): A. reasonableness check B. field check C. closed-loop verification D. validity check
Altman Distributors, Inc., fills catalog orders. Samples of size n = 100 orders have been taken each day over the past6 weeks. The average defect rate was .05. Determine the upper and lower limits for this process for 99.73% confidence.
Design specifications require that a key dimensions on a product measures 346=12 units . A process is being considered for producing this product has a standard deviation of eight units. The process average has been shifted to 350 so that the process capability is 0.3333. Approximately, what percentage of items produced will be defective?
Control charts are to be established on the manufacture of backpack frames. The revised fraction nonconforming is 0.08. Determine control limit lines for inspection rates of 1100 per day, 1500 per day, and 2100 per day. Draw the control chart. Why are the control limits not spaced equally? ( don't hand writing solution)
Daily samples of I 00 power drills are removed fromthe assembly line at Drills by Stergios Fotopoulos and inspectedfor defects. Over the past 21 days, the following information hasbeen gathered. Develop a 3 standard deviation (99.73% confidence)p-chart and graph the samples. Is the process in control?
design specifications that a key dimension on a product measure 101+16 units. A process being considered for producing this product has a standard diviation of five units. a. process capability index b. suppose the process average shifts to 96. calculate the new process capability index c. what is the probabiliy of defective output after the shift
A data entry clerk entered the incorrect part number for a blender. The part number was the part number for toasters. The best control to detect this error would include a(n): A. B. C. D.
Specifications for a part for a DVD player state that the part should weigh between 24 and 25ounces. The process that produces the parts has a mean of 24.5 ounces and a standard deviation of.2 ounce. The distribution of output is normal.a. What percentage of parts will not meet the weight specs?
Flextronchip, an OEM manufacturer, has a fifth-generation chip for cell phones, with chip specification of 0.2 ± 0.0002 mm for the distance between two adjacent pins. The loss due to a defective chip has been estimated as $28. Required: 1. Compute the value of k, the cost coefficient in the Taguchi quality loss function (QLF), L(x) = k(x − T)2. 2. Assume that the quality control manager takes a sample of 100 chips from the production process. The results are as follows: Measurement Frequency 0.1996 2 0.1997 6 0.1998 14 0.1999 9 0.2000 45 0.2001 9 0.2002 8 0.2003 5 0.2004 2 a. & b. Use the appropriate Taguchi quality loss function, L(x), to calculate the estimated quality loss for each of the observed measurements. Additionally, calculate the expected (i.e., average) loss per unit for the production process as a whole.