Create a calibration curve. Electrode potential (mV) vs. log [Ca2+]. (complete with, the equations of the best fit line, and the correlation coefficient) log[Ca 2+] Electrode potential (mV) -5 -105.4 -105.1 -106.5 -6 -120.9 -120.3 -120.6 -4.4 -96.6 -97.2 -96.5 -4 -85.5 -85.8 -85.2 -3 -56.6 -56.2 -56.4 -2 -26.6 -27.1 -27.1

Create a calibration curve. Electrode potential (mV) vs. log [Ca2+]. (complete with, the equations of the best fit line, and the correlation coefficient) log[Ca 2+] Electrode potential (mV) -5 -105.4 -105.1 -106.5 -6 -120.9 -120.3 -120.6 -4.4 -96.6 -97.2 -96.5 -4 -85.5 -85.8 -85.2 -3 -56.6 -56.2 -56.4 -2 -26.6 -27.1 -27.1

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter21: Potentiometry

Section: Chapter Questions

Problem 21.23QAP

See similar textbooks

Similar questions

A bare silver wire electrode is dipped into a solution 0.05M in KNO3 (supporting electrolyte) and saturated in AgBr (Ksp = 5.0 x 10-13), and connected to the back of an mV/pH meter along with a saturated calomel reference electrode. Calculate the potential of the silver indicator electrode. Calculate the cell potential.
Propagation of uncertainty. In an extremely accurate measurement of the Faraday constant, a pure silver anode was oxidized to Ag1 with a constant current of 0.203 639 0 (60.000 000 4) A for 18 000.075 (60.010) s to give a mass loss of 4.097 900 (60.000 003) g from the anode. Given that the atomic mass of Ag is 107.868 2 (60.000 2), find the value of the Faraday constant and its uncertainty.
An ion selective electrode for NO2- has the following values of Log k for the listed interferents. Interferent Logk F- -3.1 SO42- -4.1 I- -1.2 NO3- -3.3 Which ion is the most serious interferent? Why? For what activity of this interferent is the potential (E) equivalent to a solution in which aNO2- = 2.75 x 10-4 ?
The data below were collected using a pH electrode and a set of pH standards. What is the pH of an unknown sample if the potential reading is 200 mV? a) 3.0 b) 3.5 c) 4.0 d) 5.0 e) none of these
0.5M HA sample with 0.2 dissociation; It is placed in a conductivity cell with a length of 0.9 cm and an area of 2 cm2 and its conductivity is read as 300 mS. For this purpose;a) Equivalent conductivity of the electrolyte ?b) Boundary equivalent conductivity ?c) Decomposition constant ?
Which of the following statements is/are correct for coulometry? I. Coulometric methods count the electrons used in a chemical reaction to measure the analyte. II. Coulometry uses constant current or constant potential conditions. III. An advantage of coulometric methods is low reproducibility and a disadvantage is low sensitivity. IV. Coulometric titrations are constant potential methods. V. Constant potential methods using a three-electrode cell are more selective than constant-current methods.
A pH probe/meter uses the following equations: Ecell = L + 0.0592 log a1 = L - 0.0592 pH Where L = L1 + EAg/AgCI + Easy= constants L1 = - 0.0592 log a2 a1 = activity of analyte solution a2 = activity of internal solution Questions: How will measured pH value be affected vs “real” pH if the temperature of the sample is 30C when pH was measured? How will measured pH value be affected vs “real” pH if HCl in pH electrode, became 0.15M instead of 0.1M? How pH value will be affected vs “real” pH if the glass of the pH electrode is not fully hydrated? Please answer all questions and provide a brief explanation
When a fluoride selective electrode was immersed in a solution that is 1.0 x 10-4 M in F-, the potential that developed (versus SCE) was 41.5 mV. What will be the potential that will develop if the same electrode is immersed in a solution that is 5.0 x 10-5 M in fluoride? -51 mV -47 mV -59 mV -32 mV
By how many volts will the potential of an ideal Mg2+ ion selective electrode (ISE) change if the electrode is removed from a 1.0 x 10-4 M solution of MgCl2 and placed in 1.0 x 10-3 M MgCl2? 28 mL of 0.1M Ce4+ is mixed with 50 mL of 0.05M Fe2+. The solution potential is monitored with a Pt indicator electrode and an Ag/AgCl reference electrode. Calculate the potential of the Pt electrode and the cell potential. An ion selective electrode for NO2- has the following values of Log k for the listed interferents. Interferent Logk F- -3.1 SO42- -4.1 I- -1.2 NO3- -3.3 Which ion…
Which of the following statements is/are correct for coulometry? I. Coulometric methods count the electrons used in a chemical reaction to measure the analyte. II. Coulometry uses constant current or constant potential conditions. III. An advantage of coulometric methods is low reproducibility and a disadvantage is low sensitivity. IV. Coulometric titrations are constant potential methods. V. Constant potential methods using a three-electrode cell are more selective than constant-current methods. A). I, II and V B). I, II, IV and V C). I, III and IV D.) II, IV and V
The sensitivity of a coulometer is governed by the delivery of its minimum current for its minimum time. Suppose that 5 mA can be delivered for 0.1 s.(a) How many moles of electrons are delivered at 5 mA for 0.1 s? (b) How many milliliters of a 0.01 M solution of a two-electron reducing agent are required to deliver the same number of electrons?
Give 10 applications of Photoconductive cells