Create a diagram (handwritten) given the following conditions: a. A close circuit with 5 capacitors. b. The capacitors C1, C2, C3, C4, And C5 has a value of 2.10 μF, 2.50 µF, 2.70 µF, 2.50 µF, and 2.10 μF c. Capacitor 1, 2, and 3 are in parallel connection. d. Capacitor 4 is in series with capacitor 2. e. Capacitor 5 is in series with capacitor 1. f. The total voltage is 15.0 Volts g. Label each part of the diagram based on the conditions above. h. The diagram should be clear and complete.

Create a diagram (handwritten) given the following conditions: a. A close circuit with 5 capacitors. b. The capacitors C1, C2, C3, C4, And C5 has a value of 2.10 μF, 2.50 µF, 2.70 µF, 2.50 µF, and 2.10 μF c. Capacitor 1, 2, and 3 are in parallel connection. d. Capacitor 4 is in series with capacitor 2. e. Capacitor 5 is in series with capacitor 1. f. The total voltage is 15.0 Volts g. Label each part of the diagram based on the conditions above. h. The diagram should be clear and complete.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 68AP: A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The...

See similar textbooks

Similar questions

Two different electrical devices have the same power consumption, but one is meant to be operated on 12G-V AC and the other on 240-V AC. (a) What is the ratio of their resistances? (b) What is the ratio of their currents? (c) Assuming its resistance is unaffected, by what factor will the power increase if a 120-V AC device is connected to 240-V AC?
Integrated Concepts Use the ECG in Figure 20.34 to determine the heart rate in beats per minute assuming a constant time between beats. Figure 20.34 A lead II ECG with corresponding arterial blood pressure. The QRS complex is created by the depolarization and contraction of the ventricles and is followed shortly by the maximum or systolic blood pressure. See text for further description.
Consider the circuit below. The capacitor has a capacitance of 10 mF. The switch is closed and after a long time the capacitor is fully charged, (a) What is the current through each resistor a long time after the switch is closed? (b) What is the voltage across each resistor a long rime after the switch is closed? (c) What is the voltage across the capacitor a long time after the switch is closed? (d) What is the charge on the capacitor a long time after the switch is closed? (e) The switch is then opened. The capacitor discharges through the resistors. How long from the time before the current drops to one fifth of the initial value?
Some physical systems possessing capacitance continuously distributed over space can be modeled as an infinite array of discrete circuit elements. Examples are a microwave waveguide and the axon of a nerve cell. To practice analysis of an infinite array, determine the equivalent capacitance C between terminals X and Y of the infinite set of capacitors represented in Figure P25.47. Each capacitor has capacitance C0. Suggestions: Imagine that the ladder is cut at the line AB and note that the equivalent capacitance of the infinite section to the right of AB is also C.
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
A circuit contains a D cell battery, a switch, a 20- resistor, and four 20-mF capacitors connected in series, (a) What is the equivalent capacitance of the circuit? (b) What is the fiC time constant? (c) How long before the current decreases to 50% of the initial value once the switch is closed?
(a) Determine the equilibrium charge on the capacitor in the circuit of Figure P27.46 as a function of R. (b) Evaluate the charge when R = 10.0 . (c) Can the charge on the capacitor be zero? If so, for what value of R? (d) What is the maximum possible magnitude of the charge on the capacitor? For what value of R is it achieved? (c) Is it experimentally meaningful to take R = ? Explain your answer. If so, what charge magnitude does it imply? Figure P27.46
Integrated Concepts If you wish to take a picture of a bullet traveling at 500 m/s, then a very brief flash of light produced by an RC discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one RC constant is acceptable, and given that the flash is driven by a 600F capacitor, what is the resistance in the flash tube?
Unreasonable Results In a recording of voltages due to brain activity (an EEG), a 10.0 mV signal with a 0.500 Hz frequency is applied to a capacitor, producing a current of 100 mA. Resistance is negligible. (a) What is the capacitance? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?
Two capacitors, C1 = 25.0 F and C2 = 5.00 F, are connected in parallel and charged with a 100-V power supply. (a) Draw a circuit diagram and (b) calculate the total energy stored in the two capacitors. (c) What If? What potential difference would be required across the same two capacitors connected in series for the combination to store the same amount of energy as in part (b)? (d) Draw a circuit diagram of the circuit described in part (c).
Integrated Concepts A flashing lamp in a Christmas earring is based on an RC discharge of a capacitor through its resistance. The effective duration of the flash is 0.250 s, during which it produces in average 0.500 W from an average 3.00 V. (a) What energy does it dissipate? (b) How much charge moves through the lamp? (c) Find the capacitance. (d) What is the resistance of the lamp?
If you wish to take a picture of a bullet traveling at 500 m/s, then a very brief flash of light produced by an EC discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one EC constant is acceptable, and given that the flash is driven by a 600F capacitor, what is the resistance in the flash tube?