Current Attempt in Progress The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 775 lb/ft. Two concentrated loads also act on the rod: P = 2500 lb and Q = 800 lb. Assume a = 11 in. and b = 22 in. Determine the normal stress in the rod at the following locations: (a) x = 7 in. (b) x = 21 in. P В a b Answer: Ox=7in. psi Ox=21in. i psi

Current Attempt in Progress The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 775 lb/ft. Two concentrated loads also act on the rod: P = 2500 lb and Q = 800 lb. Assume a = 11 in. and b = 22 in. Determine the normal stress in the rod at the following locations: (a) x = 7 in. (b) x = 21 in. P В a b Answer: Ox=7in. psi Ox=21in. i psi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.1P: A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned...

See similar textbooks

Similar questions

, An arm A BC lying in a horizontal plane and supported at A (see figure) is made of two identical solid steel bars AB and BC welded together at a right angle. Each bar is 22 in. long. (a) Knowing that the maximum tensile stress (principal stress) at the top of the bar at support A due solely to the weights of the bars is 1025 psi, determine the diameter d of the bars. (b) If the allowable tensile stress is 1475 psi and each bar has a diameter d = 2.0 in,, what is the maximum downward load P that can be applied at C(in addition to self-weight
Because of foundation settlement, a circular tower is leaning at an angle a to the vertical (see figure). The structural core of the tower is a circular cylinder of height ft, outer diameter d2, and inner diameter d1.For simplicity in the analysis, assume that the weight of the tower is uniformly distributed along the height. Obtain a formula for the maximum permissible angle a if there is to be no tensile stress in the tower.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E= 15,000 ksi] rods, and a solid steel [E= 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.625 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.375 in. If all bars are unstressed before the load P is applied, determine the normal stresses in the bronze and steel rods after a load of P= 14 kips is applied.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 22 ksi, and the normal stress in steel rod (3) must be limited to 13 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 7 kips, Q = 2 kips, R = 16 kips and S = 20 kips.
The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α= 10.5 × 10−6/°F] rod (1) and a solid 1.49-in.-diameter bronze [E = 15300 ksi, v = 0.15, α= 7.6 × 10–6/°F] rod (2). Assume L1=11 in., L2=22 in. If the supports at A and C are rigid and the assembly is stress free at 16°F, determine:(a) the normal stresses σ1, σ2 in both rods at 213°F (positive if tensile, negative if compressive).(b) the displacement uB of flange B (positive if to the right, negative to the left).(c) the change in diameter Δd1 of the aluminum rod.
A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm. it fits without clearance in an 80-mm hole in a rigid block. The tube is then subjected to an internal pressure of 4.00 MPa. Assuming v=1/3 and E= 83 GPa, determine the tangential stress in the tube.
Three steel plates, each 16 mm thick and width of 300 mm are joined by two 20 mm rivets as shown. Assume the rivet hole diameter = 23 mm. A. If the load P= 50 KN, determine the tensile stress of the plates. B. If the load P= 50 KN, determine the largest bearing stress acting on the rivets. C. If the ultimate shear stress for the rivets is 180 MPa, what ultimate force Pu is required to cause the rivets to fail in shear? Neglect friction between the plates.
A rod of length L having uniform cross-sectional area A is subjected to a tensile force P . If the Young's modulus of the material varies linearly from E(1) to E(2) along the length of the rod, what is the normal stress developed at the section S-S ?
The force applied at the handle of the rigid lever causes lever to rotate 0.04 radians clockwise about the pin connection at B. if each cable is made of steel (E=200Gpa) and has a cross-sectional area of 3x10^-3m^2. Calculate a) The average normal stress in each cable? b) the force applied at E? The horizontal distance between points D and E is 200mm
The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar. b) The deflection at D for the load determined in part (a).