Customary units by using the values listed for length and mass as defined values: Bending moment or torque

Q: 4. Describe the difference between low pairs and high pairs

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: Define the term 'weight'.

A: Weight is the amount of downward force that is applied by gravity to any object in its gravitational…

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: J,ピと

A: Step 1: To obtain the natural frequency of the above given system, try to write down the motion…

Q: Describe with figures and formulas how buckling calculation is made in order to prevent damage to…

A: In various machine parts compressive force cause buckling due to which machine part may fail. For…

Q: Explain the meaning of (i) Draft and describe briefly different draft systems, (ii) Base load and…

A: Solution:: (i) The small pressure difference which causes a flow of gas to take place is termed as a…

Q: How do point loads and uniform distributed load be represented in ?SFD Curved lines and inclined…

A: the point load in shear force diagram represented in horizontal lines the uniform distributed load…

Q: 18 KN AN as

A:

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: The students are required to differentiate the following terms using the figures along with the…

A: (1) Consider the diagram shown below for simply supported and cantilever beam.

Q: shear strain produced during the operation

A: Given; Feed given to the zero degree rake angle tool is=0.2 mm/revWhere, During pure orthogonal…

Q: What is its diameter-to-length ratio for

A:

Q: What are the Regions of Concentrated Force and Moment?

A: Concentrated moments which have fixed value, Whereas Moment due to eccentric loads vary with…

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: Customary units to SI units by using the values listed for length and force as defined values:…

A: Distributed load is equal to load(force) acting per unit length of any member.

Q: -4 cm inner diameter from

A:

Q: - 100 mm 20 mm yo 140 mm -20 mm 20 mm - 100 mm

A: Rectangle Area (mm2) x¯ (in) y¯ (in) x¯y¯A (in4) I 2000 -50 70 -7000000 II 2400 0 0 0 III 2000…

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Draw the 5 major parts of an automobile that is subjected to bending and twisting moment.

A: Bending in automobile parts occurs due to loading in the vertical plane, the weight of components,…

Q: 1. How to write an introduction Introduction: i- hollow shaft, used for what, who uses it, where?…

A: **According to the guidelines we can answer only one question at a time. please resubmit the…

Q: A/ Draw (F.B.D) for the rod (200N) shown in Fig. (1-a).

A: F.B.D. consist all external force and reaction apllied on Rigid body. For solution refer below…

Q: What is the average force magnitude?

A:

Q: What is a bending moment?

A: Bending moment: Bending moment is a moment which developed in any structure or body when a force or…

Q: -r = 100 mm 50 mm -180 mm

A: As per our guidelines, experts can provide solution to only one problem in case of multiple…

Q: Describe the limiting angle of repose. Provide equations and examples to support your point

A:

Q: What is called the fit? 1) the difference between the maximum and minimum limits of size, 2) the…

A: Handwritten.jpg

Q: What is the Falling Block?

A: Falling block: The falling block is an action in which a solid metal slides vertically in a grove…

Q: 17 in 43 in E

A: refer below images.

Q: Derive an expression for the height of Proell governor.

A: The answer is in next step

Q: Define the proportional limit?

A: Stress Starin Curve: It is the curve that shows the relationship between stress and strain of a…

Q: 19.Multiple choice questions. The formulas for calculating "Equivalent force and equivalent moment…

A: Solution:

Q: m J (b)

A: for solution refer below images.

Q: The coefficient of bend value is the energy loss due to bend in a pipe depends on the pipe diameter,…

A: The loss of head due to pipe bend is given by - KV22g where V is average velocity of flow through…

Q: Which of the following statement is false related to the theory of simple bending.   The…

A: Opption (d) The value of Young's modulus is not same  is correct option

Q: speed rate, deep of cut and measurements of a meat tenderizers

A:

Q: The strains can be eliminated by using the generalized form of Hooke’slaw.True or false?

A: False, strains cannot be eliminated from the generalized hooke's law

Q: is 10 min short- dia 3 mm. Finds es hy o'mpress by 20

A:

Q: of the following causes increase in the diameter of a steam

A: Given Data : Increase in diameter of stem

Q: Differentiate enery and force

A: energy is defined as the amount of work that can be performed by force and units of the energy is…

Q: 7. What is meant by eccentric loading and eccentricity?

A: What is meant by eccentric loading and eccentricity

Q: Engineering materials can be classified as being either metals or nonmetals. Medals can be…

A:

Q: Pls answer the sub parts (ii), (iii) and (iv).

A: Consider the T-s diagram shown below for the given process.

Q: It is the study of the relationship between the external loads applied to a body and the stress and…

A: When a body is subjected to an external load then resistive force act inside the body to avoid…