Kindly answer all the parts in good handwriting with proper explanation..i will upvote afiiiigar avavA joint which is part of a loaded framework is shown below. The joint carries a vertically downward load of 18KN asshown and the horizontal force in OP is 9kN acting towards O. Give your answers to 2 decimal places.18KN8511C Cloudya)Find the force in member OR.kNb)Find the force in member OQ.kN

Answered: Image /qna-images/answer/3310fe46-3c58-4ede-bf2e-707266ed60e9.jpg

Answered: 18 KN AN as

Engineering

Mechanical Engineering

18 KN AN as

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The length of a workpiece is 5.25 in. is tapered in the lathe. If the shafting has .035 taper per…

A: GIVEN DATA- LENGTH OF WORKPIECE = 5.25in. TAPER PER FOOT = 0.035 WE HAVE TO FIND AMOUNT OF OFFSET

Q: What is the cutting speed of turning in the unit of m/min, when main axis spindle speed is 2,409 rpm…

A: Given Data N=2409 rpm D=86 mm

Q: Q4 Explain in detail the advantage of two of the following: a) Lubrication in metal forming b)…

A: a) Advantages of lubrication in metal forming In metal forming, lubricant will minimize friction and…

Q: 45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed…

Q: what is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25…

A: Given data, S = 80 stroke/min L = 1.25 feet = 15 in Find Cutting speed = V

Q: the blanks: the center distance in (cm) of 4 direct contact rolling.cylinders. Cylinders A-D have a…

Q: 1. What type of milling machine can be used to make the groove in the shaft? 2. The diameter of the…

A: 1. Grooves, elongated slots and break-throughs are produced or made for the purpose of receiving…

Q: If the ratio of the velocity of outward stroke and velocity of return stroke is 8, then the Koitie…

Q: )Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given d=22mm=0.022m spindle speed N=210rpm

Q: A steel shaft of 75 mm diameter and 250 mm long turned on a lathe Speed of spindle = 2 m/s, feed =…

A: Given:d=75 mmL=250 mmv=2 m/sf=0.25 mm/revn=50th=2 minutes/job

Q: Determine the set over to machine a taper cylinder with a major diameter 32 mm and minor diameter as…

Q: Metric thread of 0.8 mm pitch is to be cut on a lathe. Pitch of the lead screw is 1.5 mm. If the…

A: The speed of rotation of the lead screw is 800 rpm.

Q: - Formula for finding the correct tap drill size. o for English system o for Metric system - Cutting…

A: Please find the solution below

Q: Choose the right answer - In turning, the cutting force that increases by decreasing depth of cut…

A: In turning operation the cutting force is the resultant of tangential force, feed force, and radial…

Q: Determine the number of strokes per minute at which the shaper should run to machine a piece of…

A: The number of strokes per minute at which the shaper should run to machine a piece of copper is 96…

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

A: Given data Mill diameter (d) = 14 mm = 14 x 10-3 m Cutting speed (v) = 16 m/min

Q: Which of the following observations

A: Given; Two identical circular rods of same diameter same length are subjected to same magnitude of…

Q: 1. List the operations and the tools needed to make the following shape. 2. Find the speed of…

A: 1. operations and the tools needed to make the following shape are listed below:

Q: 5.53 A 15-mm-diameter hole is drilled in a piece of 20-mm-thick steel; the hole is then countersunk…

A: Given: where x-Centroid distance from the axis

Q: A 4in diameter solid shaft is used to drive the propeller of a marine vessel. It is necessary to…

A: Solid shaft: Diameter, D= 4 in Hollow shaft: Weight of the hollow shaft= (1-0.7)(Weight of the solid…

Q: It is required to cut screw threads of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If…

A: Given data: Pscrew thread=2 mmPlead screw=6 mmNs=60 rpm Need to determine the speed of lead screw.

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: Shaft.pdf

A: Shaft = 40C8 SteelRotates N=1500rpmkb=1.5kt=1.2 To-Find:- Diameter of the shaft

Q: An engineer is using a machine to cut a flat square of Aerogel of area 144 sq. c.m. If there is a…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following.…

A: In machining, taper turning is a process in which the diameter of cylindrical workpieces reduces…

Q: The blade on a typical table saw rotates at 3100 revolutions per minute. Calculate the linear…

A: Calculated the linear velocity in miles per hour of one teeth at the edge of the 10 inch diameter…

Q: nded from a rope is pulled aside with a below Calculate: -

Q: Using the Milling machine with DRO create a hallow that suites the shape of the given MILD STEEL

A: given; Using the Milling machine with DRO create a hallow that suites the shape of the given MILD…

Q: In which lathe operation, the cutting tool moves perpendicular and parallel to the axis of the…

A: Lathe is a two axis machine used to remove material from the workpiece.

Q: A chain and sprocket has a pitch diameter of 30 inches and with 90 teeth available. Find the pitch…

A: Given data, D = 30 in ( D = Pitch diameter ) T = 90 ( T = no. Of teeth ) Find pitch = P

Q: G 150mm C 250mm Block A

A: A pulley disc is a disc which is circular in nature and the main function is to provide…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following. )…

A: The most common lathe machining operation is turning. A cutting tool removes material from the…

Q: The lead screw of a lathe with nut forms a

A: A screw pair consists of a turning motion and sliding motion. The screw pair has thread cut in…

Q: rite both NC program for the workpiece shown in following figure. Stock size is 150 x135 x 15 mm.

Q: Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle…

Q: What is the stroke per minute of a mild steel which cutting speed is 200 fpm having a total length…

Q: What percentage of strength of a solid circular steel shaft of 160 mm diameter is lost by boring 100…

A: Given data as per question Diameter of solid shaft =160 mm Axial hole diameter =100 mm

Q: Solve it Properly and with right answer.

A: Case-1 Given data: The inside diameter is, di = d. The outside diameter is, do = 1.5d. Calculate…

Q: Please answer part c and e onwards with working out and answer and please label the parts as you…

A: c) TDC=Top Dead Center BDC=Bottom Dead Center Stages Ideal cycle Actual cycle Stage 1 It is…

Q: The rate of metal removal in drilling is determined as the product of the drill cross-sectional area…

A: Metal removal rate in drilling is given by:- πd^2×fN/4 where f is feed velocity and N is rpm And…

Q: Which of the following statement is correct in terms of degree of freedom? Select one: Moving…

A: For a 6 DOF system the types of translation and rotation motions are: Moving up and down…

Q: Power is supplied at the rate of 0.40 hp for 2 min in drilling a hole in a 1.0 lb brass block. (a)…

A: Given Data Power supplied at a rate of 0.40 hp for 2 min Work=Power×time Work=0.40(hp)(2×60)Work…

Q: A chain and sprocket has a pitch diameter of 9.56-inch and pitch 1/2-in .How many teeth are there in…

A: Given data, D = 9.56 in (D = Pitch diameter ) P= 0.5 in (P = Pitch) Find T = no. Of teeth = ?

Q: An engine lathe is a power-driven general-purpose machine tool used for [a )measuring material…

A: Engine lathe is a type of lathe (machinary) which has horizontal type structure , it is driven by…

Q: Q2) Choose the correct answer for only 15 (fifteen) of the following. is about 67% of the total…

A: (1) To choose: The correct option. Explanation: Turning operation: A cutting tool mounted on lathe…

Q: The blade on a typical table saw rotates at 3850 revolutions per minute. Calculate the linear…

Q: Q2 -Calculate the taper angle if the major diameter is 40.00mm and minor diameter is 28.00. The…

Q: of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If the spindle speed is 60 rpm, then…

Q: A slide in a machine is to run on rolling balls. The balls run in grooves with straight sides as…

A: Three-dimensional shapes are the focus of solid geometry. Cubes, rectangular solids, prisms,…

Q: ndly show your complete handwritten solution. Answers in m

A: SteelE=200GPa=200000MPaL=3mAluminiumE=70GPa=70000MPaL=2mP=20KNA=500mm2 To-Find:- a) Deformation of…

Concept explainers

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.

Question

Kindly answer all the parts in good handwriting with proper explanation..i will upvote

afiiiigar avav
A joint which is part of a loaded framework is shown below. The joint carries a vertically downward load of 18KN as
shown and the horizontal force in OP is 9kN acting towards O. Give your answers to 2 decimal places.
18KN
85
11C Cloudy
a)
Find the force in member OR.
kN
b)
Find the force in member OQ.
kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please answer all since they are all connected. UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The hook is used to lift the force of P as shown. The section dimensions of a-a is given: P = 40 kN a = 25 mm b = 30 mm c = 70 mm a. Calculate the distance of the centroid of section a-a from the center of curvature in mm. b. Calculate the distance of the neutral axis of section a-a from the center of curvature in mm. c. Calculate the maximum tensile stress in section a-a in MPa. d. Calculate the maximum compressive stress in section a-a in MPa.
B). Length of truss AB C).Axial force in trus BC .Enteryour answer in KN to 3 decimai places. Positive value indicites tension, negatne volue compression. D).Length of truss BC. Enter your answer in m to 2 decimal places
Answer is 4.44kN ,show work.
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The hook is used to lift the force of P as shown. The section dimensions of a-a is given: P = 40 kN a = 25 mm b = 30 mm c = 70 mm a. Calculate the distance of the centroid of section a-a from the center of curvature in mm. b. Calculate the distance of the neutral axis of section a-a from the center of curvature in mm.
7. If a force of 100 pounds is required to push a block upward an inclined purface 10 with the horizontal, what is the weight of the block? 8. 8. angle of elevation of the top of the tree from point A is 20P. At point 8, 50 m from A, the angle of elevation to the top of the tree is 22 How far is the tree from point B? 9. In order to determine the length of the bridge AB, a woman moves 250 m perpendicular to the bridge from point B to C and measures the angle at C to be 40 degrees What is the length of the bridge AB?
A force of 13,244 N will cause a 1 cm × 2 cm bar of magnesium to stretch from 10 cm to 10.05 cm. Calculate the modulus of elasticity in GPa. Round your answer to 1 decimal place.
The reaction forces created by the unbalanced loads on the shaft in the A and B bearings are given with FA = 88 j Newtons and FB= - 34 j Newtons. If the shaft rotates at 30 rad/s, find the magnitude (in Newtons) of the unbalanced loads.
GIVEN: L1=20 N GIVEN: a= 4m GIVEN: L2= 20 N GIVEN: b= 5m GIVEN: L3=20 N GIVEN: c= 6m GIVEN: L4= 0 N GIVEB: e= 3m GIVEN: L5= 10 N ANSWER: (a) Ax in N (b) Ay in N (c) Ex in N (d) Ey in N PLS SOLVE IN A COMPLETE SOLUTION AND WRITE LEGIBLY AND ALSO DRAW THE FREE BODY DIAGRAM
Q: By Assuming a=10 mm, b=40 mm in the shaded area shown in figure,
A block of with edge lengths 8.30 m. 3.20 m, 4.50 m sits on top of a pillar with a square cross section of edge length 23 cm. If the stress on the pillar is 50.5 MPa. find the density of the block in g/cm3. Round your answer to 1 decimal place.
In a hydraulic press the diameter of the plunger is 50 mm . Find the diameter of the hydraulic press side when the force at hydraulic press side is 22050 N to lift the weight at the plunger of 450N. a. 350 mm b. 250 mm c. 500 mm d. 100 mm
Pls answer, show fbd and solution