d apply the Steady Flow Energy Equation to plant equipment (P5) given in figure 2.2 where the gasses flow through e turbine at 16.57 kg/s and the power developed by the turbine is 1369.76 Kw. The specific enthalpy of the gases at inlet d outlet are 1167.75 kJ/kg are 482.5 kJ/kg respectively, and the velocities of the gases at inlet and outlet are 58.59m/s and 9.50m/ş respectively. Gasses In TURBINE W Gasses out Figure 2.2

d apply the Steady Flow Energy Equation to plant equipment (P5) given in figure 2.2 where the gasses flow through e turbine at 16.57 kg/s and the power developed by the turbine is 1369.76 Kw. The specific enthalpy of the gases at inlet d outlet are 1167.75 kJ/kg are 482.5 kJ/kg respectively, and the velocities of the gases at inlet and outlet are 58.59m/s and 9.50m/ş respectively. Gasses In TURBINE W Gasses out Figure 2.2

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 1RQ: Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop...

See similar textbooks

Similar questions

Steam enters a turbine with a pressure of P1 = (5000 – K) kPa, specific internal energy u1 = (3500 + K) kJ/kg, mass flow rate of 7.5 kg/s and density of ρ1 = [1 + (K/1000)] kg/m3. Steam leaves at P2 = (2K) kPa with a density of ρ2 = 4.5 kg/m3and a specific internal energy of u2 = (1000 + 2K) kJ/kg. Heat loss from the device by radiation is 50 kJ/kg. Neglecting the changes in kinetic and potential energies, determine the power produced by the system. k=893
A 30-kW motor drives a fan and delivers air through a duct 1.0 m x 1.0 m at 11.684 cm WG static pressure and 2.159 cm WG velocity pressure. The density of air is 1.20 kg/m³ and the density of water is 1000 kg/m³. Determine: 2. The capacity of fan, m3/s 3. Fan efficiency, %
Steam flows into a turbine at the rate of 10 kg/s and 10 KW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine. Given: h1 = 2739.0 kJ/kg : h2 = 2300.5 kJ/kg.
Seventy kilojoules of work is done by each kilogram of fluid passing through an apparatus under steady-flow conditions. In the inlet pipe, which is located 30m above the floor, the specific volume is 3m^3/kg, the pressure is 300 kPa and the velocity is 50 m/s. In the discharge pipe, which is 15 m below the floor, the specific volume is 9 m^3/kg, the pressure is 60 kPa, and the velocity is 150 m/s. Heat loss from the fluid is 3 kJ/kg. Determine the change in internal energy of the fluid passing through the apparatus.
Air flows steadily at the rate of 0.5 kg/s through an air compressor, entering at 7 m/s speed, 100 kPa pressure and 0.95 m^3/kg specific volume, leaving at 5 m/s,700 kPa, and 0.19 m^3/kg. The internal energy of the air leaving is 90 kJ/kg greater than that of the air entering. Cooling water in the compressor jackets absorbs heat from the air at the rate of 58 kW. Compute the work in kW.
3. An air compressor which operates at 900 rpm has a piston displacement of 4500cm3. Determine the mass flow rate of air at standard density considering that the volumetric efficiency is 77%. a. 314.57 kg/hr b. 324.35 kg/hr c. 137.54 kg/hr d. 224.53 kg/hr Please answer this immediately. Thank you!
1. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 lb/ft^3 and discharge it with density of 0.304 lb/ft^3. At the suction P1=15 psia; at discharge, P2=80 psia. The increase in the specific internal energy is 33.8 BTU/lb and the heat transferred from the air by cooling is 13 BTU/lb. Determine the work on the air in BTU/lb. Neglect change in kinetic energy.
A compressor draws in 0.25 m3/s of air whose density is 1.26 kg/m3 and discharges it density of 4.87 kg/m3. At the suction, P1 = 103.4 kPaa; at the discharge, P2 = 551.4 kPaa. The increase in the specific internal energy is 78.63 kJ/kg, and the heat from the air by cooling is 30.24 kJ/kg. Neglecting changes of potential and kinetic energy, determine the work on air in kW, BTU/min, and Hp.
Steam enters a turbine with a pressure of P1 = (5000 – 162) kPa, specific internal energy u1 = (350 + 162) kJ/kg, mass flow rate of 1.5 kg/s and density of 1 = [1 + (162/1000)] kg/m3. Steam leaves at P2 = (2000 + 2(162)) kPa with a density of 2 = 2.5 kg/m3 and a specific internal energy of u2 = (100 + 2(162)) kJ/kg. Heat loss from the device by radiation is 50 kJ/kg. Neglecting the changes in kinetic and potential energies, determine the power produced by the system.
A fan delivers 400 m3 /min of air at 1 atm and 21 C when rotating at 600 rpm, with a head of 8 cm WG. If the air temperature rises to 80 C with speed and air flow remains constant. Using the same fan installation as given, it is desired to maintain the same mass flow rate of air at 80 C as the mass flow rate at 21 C. Determine the new fan speed and find the new power required.
In a steady flow apparatus, a fluid enters with a specific volume of 0.30 m3/kg, a pressure of 540 kPaand a velocity of 25 m/s. The inlet port is 40m above the floor and the outlet port is at the floor level.The fluid exits with a specific volume of 0.82kg/m3, a pressure of 100 kPa and a velocity of 280 m/s.The apparatus produces 140kJ of work per kg of fluid and a 12 kJ/kg of heat loss occurs between theinlet and outlet ports. Determine the amount of change in internal energy in the apparatus in kJ/kg.Is the internal energy increases or decreases?
A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velocity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the Final Velocity in m/s if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.