10please answer the problems, the answer is already given i just need the solution please type your answer if you can because i can't view written answers NotensionFigure P-3-5,10 3-5.10. The differentiàl chain hoist in Fig. P-3-5.10 (p. 95) consists oftwo concentric pulleys rigidly fastened together. The pulleys form twosprockets for an endless chain looped over them in two loops. In one loopis mounted a movable pulley supporting a load W. Neglecting friction,determine the maximum load, W that can just be raised by a pull P appliedas shown. How is this result changed if P is not vertical?2PDW =D dAns.1.

Answered: Image /qna-images/answer/7d614882-b2b0-46b6-b51c-2e650456b827.jpg

Answered: D d No tension

Engineering

Mechanical Engineering

D d No tension

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.8P: Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the...

See similar textbooks

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the spring
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N, and its center of gravity is located at its geometric center O, the spool has a larger radius R=0,17 and an inner radius r=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel. b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
In the figure, the radius of cylinder A is 4m, cylinder B is 6m and cylinder C is 5m. Neglecting friction, a) solve For the reaction between A and B, b) reaction between the wall and B c) reaction between the Floor and A. Given: Distance between 15 KN and 40 KN load is 8m.
A rotating drum is braked by a flat belt attached to the lever ABC, hinge at B as shown in Figure. Determine the braking moment exerted by a vertical weight of 150 N. Take AB = 35 cm, BC = 65 cm and coefficient of friction between the belt and drum surface is 0.43. The radius of the drum is 0.2 m OPTIONS: 1.About 35 N-m 2.None 3.About 40 N-m 4.About 50 N-m 5.About 30 N-m 6.About 45 N-m
3. A mobile is constructed of light rods, light strings, and beach souvenirs as shown in the figure below. If m4 = 12.0 g, find values (in g) for the following. (Let d1 = 4.50 cm, d2 = 6.10 cm, d3 = 2.40 cm, d4 = 4.40 cm, d5 = 2.90 cm, and d6 = 3.50 cm.) 4. One end of a uniform 3.70-m-long rod of weight Fg is supported by a cable at an angle of ? = 37° with the rod. The other end rests against the wall, where it is held by friction as shown in the figure below. The coefficient of static friction between the wall and the rod is μs = 0.495. Determine the minimum distance x from point A at which an additional object, also with the same weight Fg, can be hung without causing the rod to slip at point A.
A 6-m long ladder has a mass of 10 kg, and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal. How far up along the ladder can a 78-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B. SOLVE ASAP
A uniform ladder stands on a rough floor and rests against a frictionless wall as shown in the figure. Since the floor is rough, it exerts both a normal force N1 and a frictional force f1 on the ladder. However, since the wall is frictionless, it exerts only a normal force N2 on the ladder. The ladder has a length of L = 4.0 m, a weight of WL = 69.0 N, and rests against the wall a distance d = 3.75 m above the floor. If a person with a mass of m = 90 kg is standing on the ladder, determine the following. (a) the forces exerted on the ladder when the person is halfway up the ladder (Enter the magnitude only.) N1 = N N2 = N f1 = N (b) the forces exerted on the ladder when the person is three-fourths of the way up the ladder (Enter the magnitude only.) N1 = N N2 = N f1 = N