Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and calculate the true position tolerance. Show your calculations. Please note: Dimensions shown is relative to the actual size As drawn 4XØ s00-0.312 e oe.0M AB C Pattern -4 holes +) +) 1.000 +) 1.500

Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and calculate the true position tolerance. Show your calculations. Please note: Dimensions shown is relative to the actual size As drawn 4XØ s00-0.312 e oe.0M AB C Pattern -4 holes +) +) 1.000 +) 1.500

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Calculate to the correct number of significant figures. 1239.3 + 9.73 + 3.42

Q: There are some incorrect indications in the following Fig.2. a) Re-draw a correct indicated drawing…

Q: The figure below shows a stepped shaft produced from a turning process on a Lathe Machine. Discuss…

A: Given Data :Length of Bar =250mmDiameter of Bar = 50mmNote : Given diameter of bar is 50mm but in…

Q: D 5 f 10 ft 10 ft 10 ft

Q: I need this part answered according to the disrections provided in the image.

A: A: It denotes sampling length and surface texture parameter symbol.B: It indicates direction of…

Q: I need the answer for problem number 14.

A: 14.In this drawing, only one chamfer is represented by the leader line. The chamfer is represented…

Q: Calculate the following slip gauges assemble to 100.115 mm. Use the of 1st, 2nd, 3nd & 4th to give…

A: (A) lets continuing with the slip guage' 100.115 - 1.005=99.11 99.11-9.11=90 90-90=0

Q: 22. Fill in the Blanks on the Charts below: Pertains to Individual Feature Only Individual Feature…

Q: 1. Most common instrument used in the mechanical gages is the dial indicator, which of the following…

A: Concept: 1) Surface roughness can't be measured with dail guage. Remaining all perpendicularity,…

Q: using the sine bar technique, find the value of the angle for the given data: the stacked height was…

Q: How many significant figures are in number? 3.12 x 10^5 km

A: One of important rule among are rule for significant digits in a number are as follows: Zeros to…

Q: Calculate to the correct number of significant figures. 1.54 x 0.03060 x 0.69

A: The number of significant figures in the number 1.54 is 3 as all digits are non-zero. The number of…

Q: Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on…

A: 1. Draw the horizontal reference line using Drafter to a some extent. 2. Draw the vertical…

Q: 36. (SI units) A GO/NO-GO plug gage will be designed to inspect a 60.00 0.40 mm diameter hole. A…

Q: Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: How many significant figures are in number? 1.563300 x 10^11 m

A: For scientific notations significant figures are calculated only for the coefficients or the…

Q: 2.36x178×106 1- 1 0.9x300x368²×30 Prequired 400 (1.18 30)

A: Given Data⇒

Q: Given the following sentence descriptions of the geometric tolerance information, correctly sketch…

Q: ᴀ ꜱᴛᴇᴇʟ ʜᴀꜱ ᴀ ʙʜɴ = 500. ᴡʜᴀᴛ ɪꜱ ɪᴛꜱ ᴀᴘᴘʀᴏxɪᴍᴀᴛᴇ ᴜʟᴛɪᴍᴀᴛᴇ ꜱᴛʀᴇɴɢᴛʜ ɪɴ ᴍᴘᴀ? a.250000 b. 2225 c.1725…

Q: ACTIVITY 48 Drow the views using the information given 30 80 55

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Identify which is the GO plug and which is the NO GO. Please explain

A: As per ISO standard design of go-no go gauge will follow as below.for solution refer below images.

Q: Assignment 8.2: Measurements and Tolerances (continued) 11. A toy company manufactures wooden blocks…

A: Consider the side of cube have measure with error of (4.5±0.1)cma. Calculate maximum surface areathe…

Q: How many significant figures are in number? 0.007 m

Q: The median value of the following set of measurements is Answer 33, 34, 33.5,35,34.5,36

A: Solution: Median value can be obtained by arranging the given values in ascending order. Therefore…

Q: the question /Like the following readings using a micrometer measuring the external dimensions…

A: given; micrometer measuring the external dimension;

Q: On the toleranced rectangle below, state the tolerance within which the top surface must be flat. O…

Q: M5.19 (Sl units) A GO/NO-GO plug gage will be designed to inspect a 50.00 0.20mm diameter hole.…

A: Calculate the tolerance band.

Q: Find the taper angle, in radians, for a workpiece if a sine bar method was used. The stacked height…

A: Sine Bar is used to measure taper angle by using gauge lengths and length of sine bar. It is the…

Q: Given the drawing below, the table shows the range of possible produced sizes and 4 optional feature…

Q: Convert 5 acre · ft to gallons. o 1629020.1945 gallons

A: Given data, Value is given 5 acre ft Find value in gallons?

Q: ᴀ ᴘᴜᴍᴘ ᴅᴇʟɪᴠᴇʀꜱ 500 ɢᴘᴍ ᴏꜰ ᴡᴀᴛᴇʀ ᴀɢᴀɪɴꜱᴛ ᴀ ᴛᴏᴛᴀʟ ʜᴇᴀᴅ ᴏꜰ 200 ꜰᴛ ᴀɴᴅ ᴏᴘᴇʀᴀᴛɪɴɢ ᴀᴛ 1770 ʀᴘᴍ. ᴄʜᴀɴɢᴇꜱ…

A: As per given question H1=200ft H2=375 ft N1=1770 rpm We have to determine N2

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: Given data: Stain=0.00021 Initial length=120 mm Find change in length

A: Given data : Strain=ε Initial length=L Required : Change in length

Q: Round off the following number to three significant figures:68.534s

A: The given no. is 68.534 s The given no. is having 5 significan figures as the number of digits are…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: 4. With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

Q: 31. (USCS units) A GO/NO-GO plug gage will be designed to inspect a 2.000 0.002 mm diameter hole. A…

A: Given data as per questionDimension of object to be inspected =2.000±0.002mmWear allowance…

Q: For an ordinary concrete slab to be laid" -3 within tolerance, engineers can only realistically…

A: Given question is related to metrology and inspection We have to complete the expression that is…

Q: 6. On an engineering drawing a dimension is laid out as 1.760 ± 0.005 A note on the drawing states…

A: (a) The nominal dimension = 1.760 inches. (b) The upper limit = 1.765 inches. (c) The tolerance = ±…

Q: You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in…

Q: Tolerance Table All dimensions in inches 11.0 + 0.4 3.1 X.X +0.1 15.00 + 0.25 3.100 Х.XX +0.05…

Q: Which type of feature doesn't belong to form tolerances? a)The profile of a surface b)Circularity…

A: Solution:

Q: I need help solving problems 7, 11, and 12 pertaining to the print provided below.

A: 7 partHidden lines are used to indicate the hidden parts of the object and these lines are dotted…

Q: Calculate to the correct number of significant figures. 0.004 + 0.09879

A: The significant figure is f=0.004+0.09879 The number after addition is f=0.004+0.09879=0.10279

Q: The time to next failure of a machine has an exponential distribution with X-0,025failure/hour.What…

Q: M5.20 (Sl units) A GO/NO-GO plug gage will be designed to inspect a 50.00 0.20mm diameter hole.…

A: Go gage will inspect the minimum shaft diameterAnd NO-GO gage will inspect maximum shaft diameter.

Q: In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70…

A: Given: Dimensions of,Hole=70+0.00+0.04mmShaft=70-0.08-0.04mm

Q: Complete the interpretation drawing for the specified tolerances. Add any required tolerance zone…

A: Complete the interpretation drawing for the specified tolerances. Add any required tolerance zone…

Q: (2) BRASS W (N) 1N 3N 6(mm) 1.58 2.86 (2) ALUMINUM W (N) 1N 3N 6(mm) 1.6 2.87 1. find the slope of…

Q: Please answer #83 82.Given a Ø24±0.25 hole located with a positional tolerance at LMC of Ø0.15,…

Concept explainers

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types:

Question

As inspected
4X Ø0.500 - 0.512
Ø0.005(M) A
B C
C
0.505
Pattern - 4 holes
#1 0.502
# 2
+)
0.504
1.002
0.506
# 3
# 4
1.503
1.505
1.003
1.004
В
A
+)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which variant of defining dimensions (A or B) would allow a higher overall part length tolerance, if the title block of the drawing holds an entry “General tolerances according to ISO 2768-m)”? Explain the reason for your answer.
Given a hole with a size dimension of Ø.875±.003 and a positional tolerance of.002 at MMC, what is the boundary that takes into consideration the combined effect of feature size at MMC and the geometric tolerance? .870 .874 .876 .880
Refer to the Ø.8740 ± .0005 dimension.A) Where is the tolerance specified ? ____________________________ B) Is its tolerance unilateral or bilaterial ? _________________________ C) What is its tolerance ? _____________________________________ D) What is the MMC, ? ________________________________ E) What is the LMC,? _________________________________
Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determine the GO and NO GO plug diameters for a hole with a dimension of φ1.875 + .003. Identify which is the GO plug and which is the NO GO. Please explain
A 30 mm diameter hole is made on a turret lathe tothe limits, 30.035 and 30.00. The followingtwo grades of shafts are used to fit in the hole:(a) φ29.955mm and 29.925mm, and (b) φ30.055mm and30.050mm.Calculate the maximum tolerance, clearance and indicatethe type of fit in each case by a sketch.ii) Suggest suitable fits and their letter and tolerancegrades for the components
Using the 10% rule of thumb for determining gagemaker’s tolerance for a plug gage, determine the GO and NO GO plug diameters for a hole with a dimension of φ2.375 + .003. Identify which is the GO and which is the NO GO.
A 150.00-mm sine bar is used to inspect a part angle that has a dimension of 35.0° ± 1.0°. The sine bar rolls have a diameter = 25.0 mm. A set of gage blocks is available that can form any height from 10.0000 mm to 199.995 mm in increments of 0.005 mm. All inspection is performed on a surface plate. Determine (a) the height of the gage block stack to inspect the minimum angle, (b) the height of the gage block stack to inspect the maximum angle, and (c) the smallest increment of angle that can be set up at the nominal angle size
two cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the solid parts of the cylinders at 40% plastic material. Given this, tell me how much plastic material is used to make each of these cylinders. I measured both cylinders in meters and these are the measurements below A) Cylinder 1- Height: 0.042m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m B) Cylinder 2 Height: 0.022m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m
need asaapp. ill reate ur answer if ur answer is correct ps: the tolerance is ±1 in the third significant digit
1. How is the location tolerance of Position different from the other 11 GD&T tolerances? Pick two (2) other tolerance and contrast write about those two in detail relative to Position tolerancing. 2. Form tolerances, elaborate how they are different from Orientation tolerances
Some hole size tolerances are specified as D7, N6, and H8. Where does the print reader find the values for those specifications? (Multiple Choice)a. In a tolerance block located in the upper-left corner of the sheetb. On line at the manufacturers websitec. A supplemental documentd. The are proprietary and not stated
Round off to 3 significant figures, and the tolerance is ±1 in the 3rd significant digit. Thank you.