D Pulley -5 ft - 8 ft -5 ft - 5 ft A B

Q: A horizontal venturimeter with inlet and throat diameters 30 cm and 15 cm respectively is used to me...

A: To Find: Rate of flow, Q Given Data: d1=30 cm=0.3 md2=15 cm=0.15 mx=20 cm of Hg=0.2 mCd=0.98

Q: While rotating at 900 rpm, a centrifugal pump delivers 2500 gpm of water at a head of 75 ft. If the ...

A: Given data as per question Rotational speed =900 rpm head =75 ft  Flow rate =2500 gpm = 5.57 ft3/s I...

Q: An orificemeter with orifice diameter 10 cm is inserted in a pipe of 20 cm diameter. The pressure ga...

A: To Find: Discharge of water through pipe, Q Given that, d0=10 cm=0.1 m(orifice),d1=20 cm=0.2 m (pipe...

Q: Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the m...

A:

Q: 4. Given a 1D elasticity problem shown in (a) of the figure below. The bar is constrained at both en...

A: Given Databar are constraints at both endsA-CA=0.1m2B-CA=0.05x-2m2E=2×107N/m2b=5N/mFor udlP=5×1=5N

Q: 1. While watering plants, a home owner is experimenting with his water hose. He sprayed the water up...

A: Answer: The plate can be suspended at the height of 3.98 m above the tip of hose.  

Q: A box is released from rest at the top of a ramp at timet = 0. It slides down the ramp and collides ...

A: Consider the time interval 0<t<tA. Let W be the weight of box so calculate the weight in the t...

Q: A cantilever beam carries a trapezoidal distributed load ( see figure) . Let wB=2.5 kN/ m, wA= 5.0kN...

A: The deflection and the angle of the free end of cantilever beam when subjected to uniformly distribu...

Q: The cross-sectional area of one limb of a U-tube manometer (figure shown below) is made 500 times la...

A: Answer: The percentage error involved is 0.2%.  

Q: A 20 in. 30° 30 in. B A) Draw a FBD of the 150 Ib cylinder. B) Find the reactions on the cylinder. C...

A: Draw free body diagram and also find reactions Given data- Weight of cylinder = 150 lb

Q: Q2/ Determine the shear stress at points A and B on the beam if it is subjected to a shear force of ...

A: Find the transverse shear stress at point A and B Given data :- Shear force = 400 kN

Q: w = 30 kN/m

A: given:  

Q: Select the word: uniform, one-dimensional, two-dimensional, or three-dimensional, that best describe...

A: Kindly refer the Solution below.

Q: A cylindrical wire which has a starting diameter of 5 mm is deformed two times to make a finer (smal...

A: Given : D = 5mm 20% reduction in area for each deformation To find : Total effective strain

Q: Consider the air flow over the wing of a civil airliner flying at M. 0.85 and at an altitude of 10,0...

A:

Q: A car of mass m performs a U-turn of radius r on a level pavement for which the coefficient of stati...

A: Given data mass of car = m coefficient of static friction = μ Radius of U-turn = r    

Q: 11.10 The acceleration of a particle is directly proportional to the square of the time t. When 1 = ...

A:

Q: In a steam power plant, saturated vapor enters the turbine at 7.5 MPa, while having a condenser pre...

A:

Q: determine: a) the pressure, volume and temperature for each state, b) the work done between 1 and 3,...

A:

Q: Find the TOTAL DEDUCTION, round your answer. Gross pay: $399 O $30.5235 O $31 O $30.52 O None of the...

A: Given Gross salary = $399 To find Total deduction

Q: 4- Single acting single cylinder compressor with diameter (15cm) and stroke length of (22.5cm).The a...

A:

Q: For storimg purposes, water is to be moved from one pool to another that is 50 ft above the first on...

A:

Q: A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional...

A: By steadly flow energy equation : h1+ V^2 /2 +g Z1+q = h2 + v^2/2+gZ2 +W Nozzle is given :- W= 0 ( n...

Q: A prismatic bar is subjected to an axial forcethat produces a tensile stress σθ = 65 u MPa and ashea...

A:

Q: Problem 2: A 4 by 4 – in. w0od – post BC is connected to a 1 – in. diameter steel eye – bar AB to fo...

A: FAy=513FA ∑Mc=0 7000*5=FA*513*7 FA=13000 lbs      (T) σAB=FAA=13000*4π*12=16552.1 psi ∑Fy=0 FC12=130...

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm.  The ...

A:

Q: A gas contained in a cylinder is compressed, the work required for compression being 9000 kJ. During...

A: For any process, internal energy can be written as the difference between heat transfer and work tra...

Q: 76. All surfaces of an infinitely long heating element, having a cross section in the shape of a cro...

A: Fins are the projection protruding from a hot surface into ambient air and they are meant for increa...

Q: is |Q|=-kA(dt/dx) the law that defines the rate of heat transfer by conduction (fourier's law of hea...

A: Q=-kAdt/dx is the Fourier's law of heat conduction which defines the rate of heat transfer by conduc...

Q: Steam generators are a type of heat exchanges that are used in power plants to generate steam at des...

A:

Q: igid support geomet in the figure and parameter table. Find the equations for the shear and moment a...

A: Given: The length of AB, L1 = 4 m The length of BC, L2 = 4 m The length of CD, L3 = 3 m The moment a...

Q: A cylinder contains a fluid at a gauge pressure of 350kPa. Express the pressure in terms of the colu...

A: Gauge pressure of fluid, Pgauge=350 kPaWater density, ρw=1000 kg/m3Specific gravity of Hg, SHG=13.6A...

Q: Q.2) If P = 160 N. Determine the moments of P about (a) point O; and (b) point C. 600 mm 360 mm

A:

Q: 5.15 The flow and head requirements for a particular application are 20 cfs and 100 ft., respectivel...

A: Given : Q = 20 cfs = 9000 gpm H = 100 ft N = 1750 rpm To find : Specific speed if connected in serie...

Q: A spherical fuel element has a center temperature of 3600 F. The fuel element is covered by two laye...

A:

Q: Person A swings from a trapeze, projects herself at angle of 53°, and is supposed to be caught by Pe...

A: Calculation of initial velocity:

Q: A В 900 N 2.25 m D 900 N 2.25 m F E 3 m Fig. P6.6

A: Find the force in each members using method of joint

Q: A two phase liquid - vapor mixture of refridgerant a2 is Contained in a ciosed tank at 10 bar. The q...

A:

Q: The truss is designed in such a way that all compression and tension members have an area of 300 mm2...

A:

Q: Calculate the total heat transfer for 12 hours through an insulated window that measures 4 ft × 7 ft...

A: Since the window is insulated, there should not be any transfer of heat between system and surroundi...

Q: Calculate the hourly heating load of a house in which all exterior surfaces have a thermal resistanc...

A: Given   Thermal resistance, R = 14 ft2.h.oF/Btu           Temperature, T1 = 65oF                    ...

Q: lve the bending stress about points A an

A: Concept:Using the bending equation we can calculate the bending stress,MI=σy=ER

Q: A long retaining wall is braced by wood shores set at an angle of 308 and supported by concrete thru...

A: Given Data The length of the wall is: 3 m The resultant force acting on the wall is: 190 kN The cro...

Q: 15. A pump operating at 660 hp delivers water, from a large pressurized supply tank to a large press...

A: Given: The pump power, P = 660 hp The water flow rate, Q = 150 ft^3/s The total length, H = 1000 ft ...

Q: A 9 ft A = 0.5 in.2 12 ft C A = 16 in.?

A: Find the stresses in each member

Q: A block of wood floats in water with 45 mm projecting above the water’s surface. When placed in glyc...

A:  It is a situation based on static equilibrium of the body in a fluid medium. The weight of the body...

Q: A slab of size 300 x 300 x 50 mm is reguire to be cast from a molten steel using a top riser of 170 ...

A: The freezing ratio is calculated by dividing the total surface area of the casting by the total volu...

Q: 5. An electric water heater has a capacity of 2 liters. In this heater, the water is initially found...

A: given; initially volume(V1)=2 lt                           =2*10-3m3initially pressure(P1)=150KPa   ...

Q: Determine the distance that the column of fluid

A: Determine the distance

Q: Hydrostatic Pressure and Force (a) A rectangular daan 20 n high and 10 in wide, Assning p= 1000 kg/m...

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.